Difficulty

Moderate

Steps

13

Time Required

Suggest a time??

Sections

3

  • Back Case
  • 4 steps
  • Motherboard
  • 6 steps
  • Digitizer and Screen
  • 3 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackSamsung Eternity

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Case
  • Remove the back battery cover.

Remove the back battery cover.

1024

Step 2

  • Remove the phone’s battery.

Remove the phone’s battery.

Step 3

  • Remove six (4.28 x 1.25)mm screws.

Remove six (4.28 x 1.25)mm screws.

Step 4

  • Use the spudger to gently pry the silver plastic back plate from the body of the phone.

Use the spudger to gently pry the silver plastic back plate from the body of the phone.

Step 5

              Motherboard
  • It is very easy to rip motherboard cables and damage fragile motherboard clips. Be careful when you are removing every component.
  • Pull the antenna plug out of its socket.

It is very easy to rip motherboard cables and damage fragile motherboard clips. Be careful when you are removing every component.

Pull the antenna plug out of its socket.

Step 6

  • Pop the two black hinged-release levers toward their ribbons, then slide the ribbons out.

Pop the two black hinged-release levers toward their ribbons, then slide the ribbons out.

Step 7

  • Pop the red hinged-release lever away from its ribbon. Then pull it out.

Pop the red hinged-release lever away from its ribbon. Then pull it out.

Step 8

  • Peel the button sensor on the side of the motherboard off of the case.

Peel the button sensor on the side of the motherboard off of the case.

Step 9

  • Slightly pull up one side of the motherboard.
  • Pull the button/microphone plug out of its socket.
  • Pop the red hinged-release lever away from its ribbon, then slide the ribbon out.

Slightly pull up one side of the motherboard.

Pull the button/microphone plug out of its socket.

Pop the red hinged-release lever away from its ribbon, then slide the ribbon out.

Step 10

  • You have successfully removed the motherboard from the phone.

You have successfully removed the motherboard from the phone.

Step 11

              Digitizer and Screen
  • Flip phone over so you are looking at the front screen of the phone. (The back is already taken off and parts removed)

Flip phone over so you are looking at the front screen of the phone. (The back is already taken off and parts removed)

Step 12

  • Use a small tool to pry the digitizer and screen (together) from the frame of the phone. This may take some time and careful work because it is glued down to the frame.
  • Be careful when you pull the lower part of this piece away from the phone frame because there is a ribbon attached to the digitizer that you don’t want to break. There is also a ribbon on the side of the screen to be aware of.

Use a small tool to pry the digitizer and screen (together) from the frame of the phone. This may take some time and careful work because it is glued down to the frame.

Be careful when you pull the lower part of this piece away from the phone frame because there is a ribbon attached to the digitizer that you don’t want to break. There is also a ribbon on the side of the screen to be aware of.

Step 13

  • Next, carefully pull the digitizer away from the screen.
  • At this point you can replace either the screen or the digitizer.
  • Cleaning the screen with a glass cleaning cloth before reassembling will remove any smudges or fingerprints from disassembling the device.

Next, carefully pull the digitizer away from the screen.

At this point you can replace either the screen or the digitizer.

Cleaning the screen with a glass cleaning cloth before reassembling will remove any smudges or fingerprints from disassembling the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 6 other contributors 


                    Heather Behrend

Member since: 04/20/2011

133 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team 15-11, Regan Spring 2011                        

                                                  Member of Cal Poly, Team 15-11, Regan Spring 2011 



                    CPSU-REGAN-S11S15G11                     


                                            5 Members                     


                                            14 Guides authored

cashyapan - May 24, 2014

Reply

You did not mention how to glue the digitizer to LCD. That is a very important step.

Brian Coukis The 90’s Kid! - Jan 22, 2019

Reply

Do these steps also work for the Samsung Eternity 2?