Difficulty

Difficult

Steps

25

Time Required

                          8 - 15 minutes

Sections

8

  • Battery
  • 2 steps
  • Top Rear Housing Cover
  • 4 steps
  • Midframe
  • 4 steps
  • Vibration Motor
  • 2 steps
  • Rear Facing Camera
  • 2 steps
  • Motherboard
  • 2 steps
  • Headphone Jack
  • 4 steps
  • Display Assembly
  • 5 steps

Flags

0

  • BackSamsung Exhibit II 4G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Insert plastic opening tool under back cover.
  • Apply pressure on tool while using a downward motion to pop off back cover.

Insert plastic opening tool under back cover.

Apply pressure on tool while using a downward motion to pop off back cover.

1024

Step 2

  • Insert plastic opening tool under battery.
  • Pry battery out.

Insert plastic opening tool under battery.

Pry battery out.

Step 3

              Top Rear Housing Cover
  • Insert plastic opening tool under back cover.
  • Pry the top cover upward to remove it from the phone.

Pry the top cover upward to remove it from the phone.

Step 4

  • Remove the top cover.

Remove the top cover.

Step 5

  • Remove the four 3.8mm Phillips #000 screws securing the top cover to the back assembly.
  • Two screws from top and two screws from back.

Remove the four 3.8mm Phillips #000 screws securing the top cover to the back assembly.

Two screws from top and two screws from back.

Step 6

  • Insert plastic opening tool under top cover.
  • Using hand slide top cover away from phone.

Insert plastic opening tool under top cover.

Using hand slide top cover away from phone.

Step 7

              Midframe
  • Remove the four 3.8mm Phillips #000 screws securing the back assembly to the phone.

Remove the four 3.8mm Phillips #000 screws securing the back assembly to the phone.

Step 8

  • Insert plastic opening tool between back assembly and phone.
  • Pry the back assembly away from phone.

Insert plastic opening tool between back assembly and phone.

Pry the back assembly away from phone.

Step 9

  • With plastic opening tool continue prying around the edge of the back assembly.

With plastic opening tool continue prying around the edge of the back assembly.

Step 10

  • Pull back panel assembly away from main body.

Pull back panel assembly away from main body.

Step 11

              Vibration Motor
  • Insert the pointed end of a spudger into the gap in the round housing frame.
  • Using spudger to remove vibrator remove from the adhesive.

Insert the pointed end of a spudger into the gap in the round housing frame.

Using spudger to remove vibrator remove from the adhesive.

Step 12

  • Use the flat end of a spudger to remove vibrator cable from motherboard.

Use the flat end of a spudger to remove vibrator cable from motherboard.

Step 13

              Rear Facing Camera
  • Use the flat end of a spudger to disconnect the camera assembly cable.

Use the flat end of a spudger to disconnect the camera assembly cable.

Step 14

  • Remove camera from square housing.

Remove camera from square housing.

Step 15

              Motherboard
  • Insert the spudger under each corner ribbon cable and lift them out of the way.
  • Use care when lifting the ribbon cables.
  • Insert a plastic pry tool into the gap between motherboard and base of phone

Insert the spudger under each corner ribbon cable and lift them out of the way.

Use care when lifting the ribbon cables.

Insert a plastic pry tool into the gap between motherboard and base of phone

Step 16

  • Tilt the motherboard up carefully.
  • Be sure not to damage the ribbon cable still connected at the bottom of the motherboard.
  • Use a spudger to pry the connector from the socket on the motherboard.
  • Lift motherboard from frame.

Tilt the motherboard up carefully.

Be sure not to damage the ribbon cable still connected at the bottom of the motherboard.

Use a spudger to pry the connector from the socket on the motherboard.

Lift motherboard from frame.

Step 17

              Headphone Jack
  • Insert flat end of spudger between support panel and front assembly.
  • Using a spudger pry up to create opening to insert plastic opening tool.

Insert flat end of spudger between support panel and front assembly.

Using a spudger pry up to create opening to insert plastic opening tool.

Step 18

  • Insert a plactic opening tool in opening.
  • Use plastic opening tool to pry around the edge of support panel to free it from front assembly.

Insert a plactic opening tool in opening.

Use plastic opening tool to pry around the edge of support panel to free it from front assembly.

Step 19

  • Insert the pointed end of a spudger into gap.
  • Lift spudger away from support plate to remove headphone component.

Insert the pointed end of a spudger into gap.

Lift spudger away from support plate to remove headphone component.

Step 20

  • Use the flat end of the spudger to remove headphone jack component from rectangular housing.

Use the flat end of the spudger to remove headphone jack component from rectangular housing.

Step 21

              Display Assembly
  • The the flat end of a spudger between componet and frame.
  • Use the the spudger to lift the componet from the frame.

The the flat end of a spudger between componet and frame.

Use the the spudger to lift the componet from the frame.

Step 22

  • Insert the spudger between blue flim and the back of the LCD.
  • Using the spudger lift blue film away from LCD.

Insert the spudger between blue flim and the back of the LCD.

Using the spudger lift blue film away from LCD.

Step 23

  • Notice ribbon cable slides under the tan square component.

Notice ribbon cable slides under the tan square component.

Step 24

  • Insert a plastic opening tool between LCD and Digitizer screen.
  • Use plastic opening tool to pry and lift the LCD from the glass screen.
  • Adhesive material around edge of LCD.

Insert a plastic opening tool between LCD and Digitizer screen.

Use plastic opening tool to pry and lift the LCD from the glass screen.

Adhesive material around edge of LCD.

Step 25

  • Lift LCD away from digitizer screen.

Lift LCD away from digitizer screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    David R

Member since: 07/20/2015

1,152 Reputation

                                      9 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Eastern Washington University, Team 1-3, Rowley SU 2015                        

                                                  Member of Eastern Washington University, Team 1-3, Rowley SU 2015 



                    EWU-ROWLEY-SU15S1G3                     


                                            4 Members                     


                                            9 Guides authored