Samsung Galaxy A5 2017 Back Cover Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Back Cover
4 steps

Flags

BackSamsung Galaxy A5 (2017)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Opening the Samsung Galaxy A5 will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally, but will loose its water-protection.

If needed, you can use a dropper or syringe to inject isopropyl alcohol (>97%) around the edges of the back cover to weaken the adhesive.

You’ll need replacement adhesive to reattach the back cover when reassembling the device.

What you need

Step 1

              Back Cover Removal

Power off your phone before beginning disassembly.
Use an iOpener to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes. You might want to repeat this step several times during the back cover removal.
The adhesive of the Samsung Galaxy A5 (2017) is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren’t able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.

Power off your phone before beginning disassembly.

Use an iOpener to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes. You might want to repeat this step several times during the back cover removal.

The adhesive of the Samsung Galaxy A5 (2017) is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren’t able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.

1024

Step 2

Insert an opening pick at the bottom end of your phone.
If you can’t manage to insert the opening pick between the back cover and the frame, you can use a suction handle to create a small gap.
Start to slide the tip of the opening pick to the bottom left corner and cut the adhesive with it.
Leave the opening pick in the bottom left corner to prevent the adhesive from resealing. Insert a new opening pick and start to cut the adhesive on the left side of the phone.

Insert an opening pick at the bottom end of your phone.

If you can’t manage to insert the opening pick between the back cover and the frame, you can use a suction handle to create a small gap.

Start to slide the tip of the opening pick to the bottom left corner and cut the adhesive with it.

Leave the opening pick in the bottom left corner to prevent the adhesive from resealing. Insert a new opening pick and start to cut the adhesive on the left side of the phone.

Step 3

Use an opening pick to cut the adhesive on all sides of the phone. Leave one opening pick in every corner to prevent the adhesive from resealing.
Reuse an iOpener if the adhesive becomes hard to cut. During the removal process the back cover is under tension all the time and is likely to break if the adhesive isn’t loose enough.
Insert an opening pick on the right side of the phone after you cut the adhesive on all sides. Flip it sideways until you can get a good grip on the back cover.

Use an opening pick to cut the adhesive on all sides of the phone. Leave one opening pick in every corner to prevent the adhesive from resealing.

Reuse an iOpener if the adhesive becomes hard to cut. During the removal process the back cover is under tension all the time and is likely to break if the adhesive isn’t loose enough.

Insert an opening pick on the right side of the phone after you cut the adhesive on all sides. Flip it sideways until you can get a good grip on the back cover.

Step 4

Remove the back cover from the phone.
Before applying new adhesive remove any remaining adhesive from the back cover and the frame and clean the areas with isopropyl alcohol and a lint-free cloth.

Remove the back cover from the phone.

Before applying new adhesive remove any remaining adhesive from the back cover and the frame and clean the areas with isopropyl alcohol and a lint-free cloth.

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond.

Cancel: I did not complete this guide.

                                                                                      18 other people completed this guide.

Author

                                      with 2 other contributors

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

Amjad Ali - Mar 22, 2020

Back glass price

Erik Astudillo - Oct 16, 2021

genial, tutorial paso a paso pregunta cual es el adhesivo que se utiliza ???

Dominik Schnabelrauch - Oct 18, 2021

Hi Erik, you can buy precut and for the A5 optimized back cover adhesive or the precut adhesive card in our shop.

The JoMan - Jan 25, 2022

Where can you buy the back glass?

Introduction#

What you need#

#

#

#

#

#

#

Team#

#

Introduction

What you need

Team