Difficulty

Moderate

Steps

17

Time Required

                          15 - 20 minutes

Sections

4

  • Battery
  • 4 steps
  • Rear Housing
  • 3 steps
  • Logic Board
  • 6 steps
  • Speaker/Rear Camera
  • 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSamsung Galaxy Attain 4G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Placement
  • Begin by turn the device over to it’s back, with the screen facing down.

Begin by turn the device over to it’s back, with the screen facing down.

1024

Step 2

              Battery Door Removal
  • At the top of the device there is a small notch that is used to remove the battery door.
  • Using a pry tool or your fingernail, pry off the battery door from the main housing.

At the top of the device there is a small notch that is used to remove the battery door.

Using a pry tool or your fingernail, pry off the battery door from the main housing.

Step 3

              Battery Removal
  • Place the battery door to the side.
  • Using a pry tool or your fingernail, pry the battery up towards you.
  • You have now removed the battery!

Place the battery door to the side.

Using a pry tool or your fingernail, pry the battery up towards you.

You have now removed the battery!

Step 4

              Heads Up!
  • Make sure when replacing the battery that the arrow on the bottom is facing down.

Make sure when replacing the battery that the arrow on the bottom is facing down.

Step 5

              Screw Removal
  • Remove the 6 Phillips head screws that hold the rear housing in place.

Remove the 6 Phillips head screws that hold the rear housing in place.

Step 6

              Prying
  • Using a spudger or plastic pry tool, slowly go around the phone between the display & rear housing to release the clips.

Using a spudger or plastic pry tool, slowly go around the phone between the display & rear housing to release the clips.

Step 7

              Remove Housing
  • Lift the rear housing from the display assembly.

Lift the rear housing from the display assembly.

Step 8

              Logic Board
  • Using your spudger/plastic pry tool, disconnect the headphone jack flex cable.

Using your spudger/plastic pry tool, disconnect the headphone jack flex cable.

Step 9

  • Using your spudger/plastic pry tool, disconnect the rear speaker flex cable.

Using your spudger/plastic pry tool, disconnect the rear speaker flex cable.

Step 10

  • Using a spudger/pry tool, carefully remove the vibration motor from its housing. This has a mild adhesive on the bottom.

Using a spudger/pry tool, carefully remove the vibration motor from its housing. This has a mild adhesive on the bottom.

Step 11

  • After removing both flex cables, slowly move the logic board to the left of the screen assembly.
  • Do not try and remove the logic board all the way, as you still have to remove the display assembly flex cable!

After removing both flex cables, slowly move the logic board to the left of the screen assembly.

Do not try and remove the logic board all the way, as you still have to remove the display assembly flex cable!

Step 12

  • Using your spudger/plastic pry tool, disconnect the LCD/Digitizer flex cable.

Using your spudger/plastic pry tool, disconnect the LCD/Digitizer flex cable.

Step 13

  • You have now removed the logic board from the display assembly.

You have now removed the logic board from the display assembly.

Step 14

              Remove Flex Cable
  • Flip the logic board to the rear side, and using a spudger/plastic pry tool to disconnect the rear camera flex cable.

Flip the logic board to the rear side, and using a spudger/plastic pry tool to disconnect the rear camera flex cable.

Step 15

  • Flip the logic board to the front, and using a spudger/plastic pry tool to push the tension clip away from the board that holds the speaker/rear camera.

Flip the logic board to the front, and using a spudger/plastic pry tool to push the tension clip away from the board that holds the speaker/rear camera.

Step 16

  • Flipping the board back over, remove the speaker/rear camera by lifting from the right side as shown.
  • Be careful not to rip the ribbon cable when you disconnect the speaker/rear camera cable connector.

Flipping the board back over, remove the speaker/rear camera by lifting from the right side as shown.

Be careful not to rip the ribbon cable when you disconnect the speaker/rear camera cable connector.

Step 17

  • The speaker/rear camera has now been removed from the board.

The speaker/rear camera has now been removed from the board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors 


                    Josh Forester

Member since: 11/28/2010

2,461 Reputation

                                      10 Guides authored                  



                       Badges:
                       31







                                                        +28 more badges