OEM Guide

Difficulty

Moderate

Steps

10

Time Required

                          15 - 30 minutes

Sections

4

  • Rubber Feet
  • 2 steps
  • Rear Case
  • 4 steps
  • Battery Disconnection
  • 2 steps
  • Battery
  • 2 steps

Flags

1

OEM Guide

iFixit collaborated with the manufacturer to make this guide.

  • BackSamsung Galaxy Book Pro 360 15"

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before you begin, refer to the Samsung PC Repair Guide for safety information.

For your safety, discharge the battery below 25% before disassembling your device. This reduces the risk of a thermal event if the battery is accidentally damaged during the repair. If your battery is swollen, take appropriate precautions.

What you need

Step 1

              Access the rubber feet
  • Before you begin, shut down your laptop and unplug it.
  • Close the screen and lay your laptop down with the rear case facing up to access the four rubber feet.

Before you begin, shut down your laptop and unplug it.

Close the screen and lay your laptop down with the rear case facing up to access the four rubber feet.

1024

Step 2

              Remove the rubber feet
  • Insert an opening pick between the rear case and the rubber foot.
  • Pry up with the pick and dislodge the foot from the rear case.
  • Use tweezers or your fingers to remove the rubber foot.
  • Repeat this process on the remaining rubber feet.
  • There are two types of rubber feet for this laptop. During reassembly, make sure the top feet say “M4” and the bottom feet say “M1”.
  • To reinstall a rubber foot, align it over the recess and push down until it’s secured.

Insert an opening pick between the rear case and the rubber foot.

Pry up with the pick and dislodge the foot from the rear case.

Use tweezers or your fingers to remove the rubber foot.

Repeat this process on the remaining rubber feet.

There are two types of rubber feet for this laptop. During reassembly, make sure the top feet say “M4” and the bottom feet say “M1”.

To reinstall a rubber foot, align it over the recess and push down until it’s secured.

Step 3

              Unfasten the rear case
  • Use a Phillips screwdriver to remove the four 4.5 mm screws securing the rear case.
  • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.
  • If you’re reassembling with the Samsung Self-Repair kit, be sure to replace the screws with new ones labeled #3313.

Use a Phillips screwdriver to remove the four 4.5 mm screws securing the rear case.

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

If you’re reassembling with the Samsung Self-Repair kit, be sure to replace the screws with new ones labeled #3313.

Step 4

              Insert an opening pick
  • Apply a suction handle to the middle of the rear case’s bottom edge, as close to the edge as possible.
  • Pull up on the handle with a strong, steady force to create a small gap between the rear case and the frame.
  • This may take significant force and multiple tries.
  • Insert an opening pick into the gap you created.

Apply a suction handle to the middle of the rear case’s bottom edge, as close to the edge as possible.

Pull up on the handle with a strong, steady force to create a small gap between the rear case and the frame.

This may take significant force and multiple tries.

Insert an opening pick into the gap you created.

Step 5

              Release the clips
  • Slide the opening pick along the bottom edge to release the clips securing the rear case.
  • Continue sliding the pick along the perimeter of the laptop until all the clips securing the rear case have been released.

Slide the opening pick along the bottom edge to release the clips securing the rear case.

Continue sliding the pick along the perimeter of the laptop until all the clips securing the rear case have been released.

Step 6

              Remove the rear case
  • Lift the rear case up and away from the laptop and remove it.
  • During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.

Lift the rear case up and away from the laptop and remove it.

During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.

Step 7

              Remove the battery connector's tape
  • Use tweezers or your fingers to peel up and remove the tape covering the battery connector.
  • Set the tape aside. You’ll reuse it during reassembly.

Use tweezers or your fingers to peel up and remove the tape covering the battery connector.

Set the tape aside. You’ll reuse it during reassembly.

Step 8

              Disconnect the battery
  • Insert the flat end of a spudger under the battery cables, as close to the connector as possible.
  • Gently pry up and disconnect the battery connector from its socket.

Insert the flat end of a spudger under the battery cables, as close to the connector as possible.

Gently pry up and disconnect the battery connector from its socket.

Step 9

              Unfasten the battery
  • Use a Phillips screwdriver to remove the four 4.5 mm screws securing the battery.
  • Take care not to puncture the battery with your screwdriver—a punctured battery may leak dangerous chemicals or cause a fire.

Use a Phillips screwdriver to remove the four 4.5 mm screws securing the battery.

Take care not to puncture the battery with your screwdriver—a punctured battery may leak dangerous chemicals or cause a fire.

Step 10

              Remove the battery
  • Lift the battery straight out of its recess and remove it.

Lift the battery straight out of its recess and remove it.

To reassemble your device, follow the instructions in reverse order and perform the opposite actions, e.g., “reattach” instead of “removing.” Skip steps that use heating and prying, and pay close attention to the 📌 bullets as you work through the steps.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Spencer Day

Member since: 09/14/2022

11,019 Reputation

                                      84 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored