Samsung Galaxy Camera 2 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          10 minutes            

Sections

2

• Battery
• 4 steps
• Screen
• 6 steps

Flags

0

• BackSamsung Galaxy Camera 2

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Face the camera towards you, then rotate it such that the battery door is facing up and to the right.

Face the camera towards you, then rotate it such that the battery door is facing up and to the right.

1024

Step 2

• Locate the small latch on the right side of the camera.
• Slide the latch to the left to open the battery compartment door.

Locate the small latch on the right side of the camera.

Slide the latch to the left to open the battery compartment door.

Step 3

• Locate the battery, a black cell held in by a small clip (indicated by an outfacing arrow).
• Pull the clip toward you to release the battery.

Locate the battery, a black cell held in by a small clip (indicated by an outfacing arrow).

Pull the clip toward you to release the battery.

Step 4

• Remove and discard the old battery.

Remove and discard the old battery.

Step 5

              Screen               

• While holding the camera, take note of each screw holding the screen to the main chassis of the camera.
• Hold the camera upright and lens facing towards you. There area total of six 4mm PH00 screws to undo - two on the left, one screw on the right, and three along the bottom. Two of them are hidden behind the battery compartment door.

While holding the camera, take note of each screw holding the screen to the main chassis of the camera.

Hold the camera upright and lens facing towards you. There area total of six 4mm PH00 screws to undo - two on the left, one screw on the right, and three along the bottom. Two of them are hidden behind the battery compartment door.

Step 6

• Use the screwdriver to remove screws listed in step 2. There are a total of six 4mm screws.

Use the screwdriver to remove screws listed in step 2. There are a total of six 4mm screws.

Step 7

• With the screws removed, use the plastic opening tool to gently pry the screen away from the main camera chassis. The ideal spot to start is at the corner with the headphone jack, as indicated in the picture.
• Once this side is free, gently work your way along the edge, all the way around the camera body.

With the screws removed, use the plastic opening tool to gently pry the screen away from the main camera chassis. The ideal spot to start is at the corner with the headphone jack, as indicated in the picture.

Once this side is free, gently work your way along the edge, all the way around the camera body.

Step 8

• With the screen freed, gently lay the camera on its face, so that the battery compartment faces up. Use both hands to lift the screen up and away.
• The screen is still attached to the motherboard by a ribbon cable. Be Gentle as it’s very fragile.

With the screen freed, gently lay the camera on its face, so that the battery compartment faces up. Use both hands to lift the screen up and away.

The screen is still attached to the motherboard by a ribbon cable. Be Gentle as it’s very fragile.

Step 9

• With the screen separated from the main chassis, use the plastic opening tool to gently pry the edge of the ribbon cable connector from the motherboard.

With the screen separated from the main chassis, use the plastic opening tool to gently pry the edge of the ribbon cable connector from the motherboard.

Step 10

              Screen Separated               

• Now the screen is removed.
• Set the body aside in a safe place.

Now the screen is removed.

Set the body aside in a safe place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.                                             

Author

                                      with 7 other contributors 

                    Alexander De La Cruz                     

Member since: 02/10/2016

619 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges                           

Team

                       USF Tampa, Team 14-5, Lacy Spring 2016                        

                                                  Member of USF Tampa, Team 14-5, Lacy Spring 2016 



                    USFT-LACY-S16S14G5                     


                                            3 Members                     


                                            13 Guides authored                     

nicole deltondo - Jul 16, 2016

Reply

I need to replace the screen and keep the. White around it. How do I do that

clhowey - Sep 9, 2016

You have to use a hair dryer on high on the screen until you can get it loose from the white frame. Carefully pry under the screen with a small screwdriver or a plastic tool to get it loose and then run the plastic tool around the edges until it is loose. It is held in by some type of double sided tape.

Richard Trinidad - Aug 6, 2016

Reply

after part sales comes only with lcd screen, my question is how do you remove the broken lcd from the housing?

James - Jun 3, 2017

Reply

So what do i use to keep the new one attached?

Jasper Walker - Feb 3, 2018

Reply

This is a incomplete guide.