Difficulty
Moderate
Steps
11
Time Required
30 minutes
Sections
1
- Headphone Jack
- 11 steps
Flags
3
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
Step Trimmer
This guide has unnecessary steps. Trim them to be more concise!
BackSamsung Galaxy Player 5.0
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Headphone Jack
- Remove the SD Memory Card before taking the device apart. Using the screwdriver, remove the 10mm Phillips screw that is near the SD Memory Card port.
Remove the SD Memory Card before taking the device apart. Using the screwdriver, remove the 10mm Phillips screw that is near the SD Memory Card port.
1024
Step 2
- Remove the white caps which are covering the screws that are located on either side of the charging port.
- You may have to use a low heat blow dryer for 5 to 10 seconds, or other equivalent heat source to loosen the adhesive.
Remove the white caps which are covering the screws that are located on either side of the charging port.
You may have to use a low heat blow dryer for 5 to 10 seconds, or other equivalent heat source to loosen the adhesive.
Step 3
- Continue to unscrew the two 10mm Phillips Screws from the bottom of the device.
Continue to unscrew the two 10mm Phillips Screws from the bottom of the device.
Step 4
- Starting from the bottom and working around, use an opening pick to separate the front cover housing from the back cover housing.
- You will hear a popping sound, indicating the separation.
Starting from the bottom and working around, use an opening pick to separate the front cover housing from the back cover housing.
You will hear a popping sound, indicating the separation.
Step 5
- Take the back housing cover off of the device.
Take the back housing cover off of the device.
Step 6
- Detach the tab the battery is attached to and the battery using the prying tool in an upward motion.
- Adhesive is behind the battery, but it is not strong.
Detach the tab the battery is attached to and the battery using the prying tool in an upward motion.
Adhesive is behind the battery, but it is not strong.
Step 7
- Remove the headphone jack by unscrewing the 10mm Phillips screw to its left then proceed to pry up the tab that attaches the headphone jack to the motherboard.
Remove the headphone jack by unscrewing the 10mm Phillips screw to its left then proceed to pry up the tab that attaches the headphone jack to the motherboard.
Step 8
- Place new the headphone jack back into its position and connect the tab, then screw it back into place.
Place new the headphone jack back into its position and connect the tab, then screw it back into place.
Step 9
- Insert the battery into its position, and reconnect its tab onto the motherboard.
Insert the battery into its position, and reconnect its tab onto the motherboard.
Step 10
- Now put the rear housing cover on the device, starting from its bottom side, and snap the edges all the way around to close the device.
Now put the rear housing cover on the device, starting from its bottom side, and snap the edges all the way around to close the device.
Step 11
- Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port.
Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 4 other contributors
China Ayala
Member since: 03/05/2015
584 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
Sam Houston State, Team 11-7, Blackburne Winter 2015
Member of Sam Houston State, Team 11-7, Blackburne Winter 2015
SHSU-BLACKBURNE-W15S11G7
3 Members
8 Guides authored
