Difficulty
Difficult
Steps
14
Time Required
2 hours
Sections
6
- Case
- 1 step
- Battery
- 3 steps
- Loudspeaker Modules
- 3 steps
- Rear Camera
- 1 step
- Motherboard
- 2 steps
- Screen
- 4 steps
Flags
2
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackSamsung Galaxy Note 10.1 (2014)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
It is based on
and
Actually you need only to remove the battery but I removed the motherboard etc. for safety reasons.
What you need
Step 1
Case
- Using the nylon spudger or plastic opening tool along the edges of the screen, separate the back case off of the device.
- If possible, consider using the black nylon spudger for a gentler separation.
Using the nylon spudger or plastic opening tool along the edges of the screen, separate the back case off of the device.
If possible, consider using the black nylon spudger for a gentler separation.
1024
Step 2
Battery
- Place your finger on the thin black bar at the end of the ribbon tape and flip each one up.
- Gently pull the ribbon tape on the battery away from the bar. Repeat this process for the second ribbon tape.
Place your finger on the thin black bar at the end of the ribbon tape and flip each one up.
Gently pull the ribbon tape on the battery away from the bar. Repeat this process for the second ribbon tape.
Step 3
- Remove the six 3mm screws around the battery with the Phillips PH000 screwdriver.
Remove the six 3mm screws around the battery with the Phillips PH000 screwdriver.
Step 4
- Lift up the battery from the bottom and situate the black nylon spudger underneath the battery.
- Use the black nylon spudger to disconnect the multi-colored wires from the rest of the device.
Lift up the battery from the bottom and situate the black nylon spudger underneath the battery.
Use the black nylon spudger to disconnect the multi-colored wires from the rest of the device.
Step 5
Loudspeaker Modules
- Remove the three 3mm screws on the top right side of the device with the Phillips PH000 screw head.
- Remove the one 3mm screw on the top left side of the device with the same method.
Remove the three 3mm screws on the top right side of the device with the Phillips PH000 screw head.
Remove the one 3mm screw on the top left side of the device with the same method.
Step 6
loudspeaker - remove right speaker
- Remove the gray rubber piece.
- Use a spudger or fingernail to disconnect the blue antenna cable from the motherboard.
- Remove the right speaker unit.
Remove the gray rubber piece.
Use a spudger or fingernail to disconnect the blue antenna cable from the motherboard.
Remove the right speaker unit.
Step 7
- Remove the loudspeaker modules located on the parts where the screws were removed by using the black nylon spudger.
- They are the black pieces at the top left and right corners of the device that have metal squares on them in the middle.
Remove the loudspeaker modules located on the parts where the screws were removed by using the black nylon spudger.
They are the black pieces at the top left and right corners of the device that have metal squares on them in the middle.
Step 8
Rear Camera
- Disconnect the camera piece from the motherboard.
- The camera piece is shaped like an “L”.
Disconnect the camera piece from the motherboard.
The camera piece is shaped like an “L”.
Step 9
Motherboard
- Disconnect all cables on the motherboard.
- See our connector guide for help safely disconnecting various types of connectors.
Disconnect all cables on the motherboard.
See our connector guide for help safely disconnecting various types of connectors.
Step 10
- Use the black nylon spudger to gently lift the motherboard away from the frame.
- Remove the motherboard.
Use the black nylon spudger to gently lift the motherboard away from the frame.
Remove the motherboard.
Step 11
sreen - remove middle frame
- remove middle frame by pulling it off
remove middle frame by pulling it off
Step 12
screen - seperate LCD and Screen
- follow as shown on TechGuru.gr
- Screen burst, be aware of glass splinters. May you cover the screen with tissue
follow as shown on TechGuru.gr
Screen burst, be aware of glass splinters. May you cover the screen with tissue
Step 13
screen - seperate buttons from screen
- buttons are glued to frame, gently lift up screen
- pull of cable, connecting the buttons, gently
buttons are glued to frame, gently lift up screen
pull of cable, connecting the buttons, gently
Step 14
screen - clean
- rub of the glue with the fingers
- remove residues with makeup remover or similar
rub of the glue with the fingers
remove residues with makeup remover or similar
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 2 other contributors
Stefn Mueller
Member since: 12/23/2015
403 Reputation
1 Guide authored
Badges:
8
+5 more badges
Amiel D Hechanova - Sep 27, 2018
Reply
is the digitizer glued to the lcd screen?
Stefn Mueller - Sep 27, 2018
Reply
it is see referenced YouTube video
Paul Brook - Dec 16, 2018
Reply
The e battery and screen cable clasps that hold tge cables in….. Where do i get them repaired
Hi can somebody help me
