Difficulty

Moderate

Steps

11

Time Required

Suggest a time??

Sections

6

  • Rear Case
  • 2 steps
  • Battery
  • 1 step
  • S Pen
  • 1 step
  • Midframe
  • 2 steps
  • Motherboard
  • 3 steps
  • Headphone Jack
  • 2 steps

Flags

0

  • BackSamsung Galaxy Note 3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the rear case
  • Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.

Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.

1024

Step 2

              Remove Case from the Base
  • Slide your fingernail or plastic opening tool along the edge of the rear case.
  • Lift the case gently from the base.

Slide your fingernail or plastic opening tool along the edge of the rear case.

Lift the case gently from the base.

Step 3

              Battery
  • Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base.
  • Lift the battery out of its recess.

Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base.

Lift the battery out of its recess.

Step 4

              S Pen
  • Place your fingernail in the groove of the stylus pen.
  • Pull the stylus pen away from the phone.

Place your fingernail in the groove of the stylus pen.

Pull the stylus pen away from the phone.

Step 5

              Unscrew Back Chassis
  • Remove the twelve 4mm Phillips #00 screws from the back chassis.

Remove the twelve 4mm Phillips #00 screws from the back chassis.

Step 6

              Remove Back Chassis
  • Insert the plastic opening tool into the Stylus Pen placement holder.
  • Lift the plastic opening tool so that the midframe separates from the base.

Insert the plastic opening tool into the Stylus Pen placement holder.

Lift the plastic opening tool so that the midframe separates from the base.

Step 7

              Screw Removal
  • Remove the single screw beside headphone jack.

Remove the single screw beside headphone jack.

Step 8

              Unfasten Clips and Cable Connectors
  • Use tweezers to remove both antenna clips.
  • Use a spudger to disconnect six cable connectors.

Use tweezers to remove both antenna clips.

Use a spudger to disconnect six cable connectors.

Step 9

              Motherboard Removal
  • Pull up on the motherboard with tweezers.

Pull up on the motherboard with tweezers.

Step 10

              Spudger Tool Placement
  • Insert the spudger into the headphone jack.

Insert the spudger into the headphone jack.

Step 11

              Lift to Separate Headphone Jack
  • Lift the spudger to separate the jack assembly from the motherboard.
  • Pull to remove.

Lift the spudger to separate the jack assembly from the motherboard.

Pull to remove.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      23 other people completed this guide.

Author

                                      with 4 other contributors 


                    Brittany Gail

Member since: 09/23/2014

8,463 Reputation

                                      8 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Team

                       USF Tampa, Team 2-2, Blackwell Fall 2014                        

                                                  Member of USF Tampa, Team 2-2, Blackwell Fall 2014 



                    USFT-BLACKWELL-F14S2G2                     


                                            4 Members                     


                                            25 Guides authored