Samsung Galaxy Note Edge Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

7

Time Required

                          10 - 15 minutes            

Sections

2

• Battery
• 2 steps
• Motherboard
• 5 steps

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Missed a Step

Oops! This guide is currently missing some important steps.

• BackSamsung Galaxy Note Edge

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Power down your device and make sure that it is turned off.
• Place the phone with the screen facing down on a clean flat surface.

Power down your device and make sure that it is turned off.

Place the phone with the screen facing down on a clean flat surface.

1024

Step 2

• Use your Supdger to remove the back cover of the phone using notch located in the top left corner of the phone.
• Remove battery by using your Supdger on the notch located directly underneath battery location.
• During the creation of this guide, we did not have access to a battery in our device.

Use your Supdger to remove the back cover of the phone using notch located in the top left corner of the phone.

Remove battery by using your Supdger on the notch located directly underneath battery location.

During the creation of this guide, we did not have access to a battery in our device.

Step 3

              Motherboard               

• Remove the SIM Card from the SIM Card holder by gently sliding the SIM Card horizontally.
• Remove the stylus from the stylus holder.

Remove the SIM Card from the SIM Card holder by gently sliding the SIM Card horizontally.

Remove the stylus from the stylus holder.

Step 4

• Using a Phillips #000 Screwdriver, remove the fifteen 4mm screws that secure the rear chassis.
• Insert your spudger into the stylus socket and pry the midframe from the phone.
• Move the spudger around edge of phone, carefully prying the midframe from the phone until midframe is entirely separated.

Using a Phillips #000 Screwdriver, remove the fifteen 4mm screws that secure the rear chassis.

Insert your spudger into the stylus socket and pry the midframe from the phone.

Move the spudger around edge of phone, carefully prying the midframe from the phone until midframe is entirely separated.

Step 5

• With the pointed end of your spudger, disconnect the two wires (pink and white) located near the bottom of the phone.
• Using pointed end of your dpudger, disconnect the finger print scanner cable- it is located directly above the pink and white cables.

With the pointed end of your spudger, disconnect the two wires (pink and white) located near the bottom of the phone.

Using pointed end of your dpudger, disconnect the finger print scanner cable- it is located directly above the pink and white cables.

Step 6

• Using your Spudger’s pointed end, pry off the following leads that connect these parts to the logic board in the top left hand corner:
• Front Facing Camera
• AMOLED Display Screen
• AMOLED Capacitive Screen

Using your Spudger’s pointed end, pry off the following leads that connect these parts to the logic board in the top left hand corner:

Front Facing Camera

AMOLED Display Screen

AMOLED Capacitive Screen

Step 7

• At the top end, gently insert pointed end of spudger underneath the motherboard.
• Lift the motherboard up gently. Disconnect the cable connecting the daughter board. It is attached to the underside of the motherboard.
• Remove the motherboard from the device.

At the top end, gently insert pointed end of spudger underneath the motherboard.

Lift the motherboard up gently. Disconnect the cable connecting the daughter board. It is attached to the underside of the motherboard.

Remove the motherboard from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Matt Clark                     

Member since: 04/19/2018

157 Reputation

                                      1 Guide authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Cal Poly, Team S22-G6, Maness Spring 2018                        

                                                  Member of Cal Poly, Team S22-G6, Maness Spring 2018 



                    CPSU-MANESS-S18S22G6                     


                                            4 Members                     


                                            10 Guides authored