Difficulty
Moderate
Steps
19
Time Required
Suggest a time??
Sections
8
- Stylus
- 1 step
- Rear Case
- 2 steps
- Battery
- 1 step
- MicroSD Card
- 2 steps
- SIM Card
- 2 steps
- Midframe
- 5 steps
- Upper Display Assembly Bracket
- 3 steps
- Headphone Jack/Earpiece Speaker Assembly
- 3 steps
Flags
0
BackSamsung Galaxy Note
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Stylus
- Grasp the cap of the stylus and remove it from its slot in the midframe.
Grasp the cap of the stylus and remove it from its slot in the midframe.
1024
Step 2
Rear Case
- Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.
Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.
Step 3
- Lift and remove the rear case from the phone.
Lift and remove the rear case from the phone.
Step 4
Battery
- Insert your finger in the notch of the battery compartment.
- Press the battery toward the rear facing camera while pulling outward.
Insert your finger in the notch of the battery compartment.
Press the battery toward the rear facing camera while pulling outward.
Step 5
MicroSD Card
- Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
- After the click, release the card and it will pop out of its slot.
- For reassembly, push the microSD card into the slot until it clicks in place.
Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
After the click, release the card and it will pop out of its slot.
For reassembly, push the microSD card into the slot until it clicks in place.
Step 6
- Remove the microSD card from its slot in the midframe.
Remove the microSD card from its slot in the midframe.
Step 7
SIM Card
- Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.
Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.
Step 8
- Slide the SIM card out the rest of the way with your thumb and remove it from the device.
Slide the SIM card out the rest of the way with your thumb and remove it from the device.
Step 9
Midframe
- Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.
Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.
Step 10
- Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.
Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.
Step 11
- Slide the plastic opening tool down the seam.
Slide the plastic opening tool down the seam.
Step 12
- Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly.
- Slide the opening tool along the top edge of the phone.
- Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.
Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly.
Slide the opening tool along the top edge of the phone.
Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.
Step 13
- Remove the midframe from the display assembly.
Remove the midframe from the display assembly.
Step 14
Upper Display Assembly Bracket
- Use the flat end of a spudger to disconnect the headphone jack/earpiece speaker assembly cable connector.
Use the flat end of a spudger to disconnect the headphone jack/earpiece speaker assembly cable connector.
Step 15
- Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.
Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.
Step 16
- Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.
Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.
Step 17
Headphone Jack/Earpiece Speaker Assembly
- Use the flat end of a spudger to disconnect the headphone jack/earpiece speaker assembly connector.
Use the flat end of a spudger to disconnect the headphone jack/earpiece speaker assembly connector.
Step 18
- Use the point of a spudger to pry the headphone jack out of its recess in the display assembly.
Use the point of a spudger to pry the headphone jack out of its recess in the display assembly.
Step 19
- Use a pair of tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly from the display assembly.
Use a pair of tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly from the display assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
11 other people completed this guide.
Author
with 1 other contributor
Sam Goldheart
Member since: 10/18/2012
455,549 Reputation
548 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
John Cobra - Jul 11, 2014
Reply
I’d recommend getting an Original part if possible, the knock off speaker has no metal casing where the original does.
