Samsung Galaxy Note5 Volume Button Replacement Repair Guide

Difficulty

Moderate

Steps

14

Time Required

                          25 - 30 minutes            

Sections

3

• SIM Card Tray
• 2 steps
• Power Button
• 10 steps
• Volume Button
• 2 steps

Flags

0

• BackSamsung Galaxy Note 5

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              SIM Card Tray               

• Insert a SIM Ejector Tool into the small hole on the left side of the top edge of the device.
• Press down until the SIM Card Tray begins to protrude out of the device.

Insert a SIM Ejector Tool into the small hole on the left side of the top edge of the device.

Press down until the SIM Card Tray begins to protrude out of the device.

1024

Step 2

• Remove the SIM Card Tray from the slot.

Remove the SIM Card Tray from the slot.

Step 3

              Power Button               

• Heat the back of the device with a heat gun for 2 minutes

Heat the back of the device with a heat gun for 2 minutes

Step 4

• Once the device is heated, place a suction cup near the bottom of the back of the device Make sure it is placed on the flat part of the glass
• Be careful holding the device after heating the back, it may burn!
• Gently pull upwards on the suction cup to separate the rear glass from the body of the phone.
• While pulling upwards, insert a pick under the rear glass

Once the device is heated, place a suction cup near the bottom of the back of the device Make sure it is placed on the flat part of the glass

Be careful holding the device after heating the back, it may burn!

Gently pull upwards on the suction cup to separate the rear glass from the body of the phone.

While pulling upwards, insert a pick under the rear glass

Step 5

• Keeping the pick under the rear glass, move the pick along the bottom edge of the device to cut the adhesive.

Keeping the pick under the rear glass, move the pick along the bottom edge of the device to cut the adhesive.

Step 6

• Repeat the previous heating and cutting procedure for the remaining three sides of the phone.
• Leave a pick on each side as you continue to the next to prevent the adhesive from resealing.

Repeat the previous heating and cutting procedure for the remaining three sides of the phone.

Leave a pick on each side as you continue to the next to prevent the adhesive from resealing.

Step 7

• Once all adhesive has been cut, gently lift up the rear glass to remove it.

Once all adhesive has been cut, gently lift up the rear glass to remove it.

Step 8

• Remove the S-Pen from the bottom of the device

Remove the S-Pen from the bottom of the device

Step 9

• Remove 20 5mm screws with a Phillips #1 Screwdriver.

Remove 20 5mm screws with a Phillips #1 Screwdriver.

Step 10

• Grip the back of the device and press down on the white square to remove the middle housing.

Grip the back of the device and press down on the white square to remove the middle housing.

Step 11

• Loosen the power button flex adhesive by holding it with the tweezers.
• With the tweezers, pry up and remove the power button flex

Loosen the power button flex adhesive by holding it with the tweezers.

With the tweezers, pry up and remove the power button flex

Step 12

• Push out the power button with the tip of the tweezers.

Push out the power button with the tip of the tweezers.

Step 13

              Volume Button               

• Loosen the volume flex adhesive.
• Pry up and remove the volume button flex.

Loosen the volume flex adhesive.

Pry up and remove the volume button flex.

Step 14

• Push out the volume button and remove it from the device.

Push out the volume button and remove it from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Bernice Nunez                     

Member since: 04/19/2018

313 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       Cal Poly, Team S25-G17, Maness Spring 2018                        

                                                  Member of Cal Poly, Team S25-G17, Maness Spring 2018 



                    CPSU-MANESS-S18S25G17                     


                                            4 Members                     


                                            5 Guides authored