Samsung Galaxy S4 Active Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          40 - 45 minutes            

Sections

7

• Rear Case
• 1 step
• MicroSD Card
• 1 step
• Battery
• 1 step
• SIM Card
• 1 step
• Midframe
• 2 steps
• Motherboard
• 3 steps
• Display Assembly
• 1 step

Flags

2

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackSamsung Galaxy S4 Active

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Rear Case               

• Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
• Lift the rear case by the corner nearest the divot and remove it from the phone.

Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.

Lift the rear case by the corner nearest the divot and remove it from the phone.

1024

Step 2

              MicroSD Card               

• Use a plastic opening tool, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
• After the click, release the card and it will pop out of its slot.
• Remove the microSD card.

Use a plastic opening tool, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

After the click, release the card and it will pop out of its slot.

Remove the microSD card.

Step 3

              Battery               

• Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward to remove it.

Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward to remove it.

Step 4

              SIM Card               

• Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.
• After the click, release the card and it will pop out of its slot.
• Remove the SIM card.

Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.

Remove the SIM card.

Step 5

              Midframe               

• Use the tip of a spudger to remove the four metallic pads located in each corner of the device.
• Using a Phillips #00 screwdriver, remove the 12 screws connecting the midframe to the device.

Use the tip of a spudger to remove the four metallic pads located in each corner of the device.

Using a Phillips #00 screwdriver, remove the 12 screws connecting the midframe to the device.

Step 6

• Use the plastic opening tool to pry around the entire edge of the midframe now to release it from the front case.

Use the plastic opening tool to pry around the entire edge of the midframe now to release it from the front case.

Step 7

              Motherboard               

• Use the flat end of a plastic opening tool to disconnect the USB board connector.
• Disconnect the front-facing camera cable connector.
• Disconnect the earpiece speaker assembly cable connector.
• Disconnect the headphone jack assembly cable connector.
• Disconnect the display/digitizer cable connector.
• Disconnect the antenna cable connector.

Use the flat end of a plastic opening tool to disconnect the USB board connector.

Disconnect the front-facing camera cable connector.

Disconnect the earpiece speaker assembly cable connector.

Disconnect the headphone jack assembly cable connector.

Disconnect the display/digitizer cable connector.

Disconnect the antenna cable connector.

Step 8

• Remove the single 2.4 mm Phillips #00 screw from the motherboard assembly.

Remove the single 2.4 mm Phillips #00 screw from the motherboard assembly.

Step 9

• Remove the motherboard.

Remove the motherboard.

Step 10

              Display Assembly               

• Disconnect the daughterboard connector from the frame.
• Slowly peel off the daughterboard and remove it from the device.

Disconnect the daughterboard connector from the frame.

Slowly peel off the daughterboard and remove it from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Justin Ogihara                     

Member since: 09/18/2017

23,793 Reputation

                                      52 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges                           

Team

                       EDU Team                        

                                                  Member of EDU Team 



                    Community                     


                                            7 Members                     


                                            487 Guides authored