Difficulty
Moderate
Steps
12
Time Required
Suggest a time??
Sections
6
- Rear Case
- 2 steps
- MicroSD Card
- 1 step
- Battery
- 1 step
- SIM Card
- 1 step
- Midframe
- 6 steps
- Speaker Enclosure
- 1 step
Flags
0
BackSamsung Galaxy S4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Case
- Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
1024
Step 2
- Lift the rear case by the corner nearest the divot and remove it from the phone.
Lift the rear case by the corner nearest the divot and remove it from the phone.
Step 3
MicroSD Card
- Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
- After the click, release the card and it will pop out of its slot.
- Remove the microSD card.
- For reassembly, push the microSD card into the slot until it clicks in place.
Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
After the click, release the card and it will pop out of its slot.
Remove the microSD card.
For reassembly, push the microSD card into the slot until it clicks in place.
Step 4
Battery
- Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
- Remove the battery from your phone.
Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
Remove the battery from your phone.
Step 5
SIM Card
- Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.
- After the click, release the card and it will pop out of its slot.
- Remove the SIM card.
- During reassembly, push the SIM card into the slot until it clicks in place.
Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.
Remove the SIM card.
During reassembly, push the SIM card into the slot until it clicks in place.
Step 6
Midframe
- Remove the nine 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
Remove the nine 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
Step 7
- The midframe is secured to the display assembly by several plastic clips behind the chrome bezel of the midframe. The next few steps will guide you through separating the clips to free the midframe.
- Starting on the volume button side of the phone, insert your plastic opening tool between the chrome bezel around the display glass and the larger chrome border piece. Look for the seam between the two.
- Slide the opening tool along the seam, separating the plastic clips as you go.
- Be very gentle whilst prying, and pry only enough to separate the plastic clips—there are several thin points in the midframe bezel that may crack if you bend them too much.
The midframe is secured to the display assembly by several plastic clips behind the chrome bezel of the midframe. The next few steps will guide you through separating the clips to free the midframe.
Starting on the volume button side of the phone, insert your plastic opening tool between the chrome bezel around the display glass and the larger chrome border piece. Look for the seam between the two.
Slide the opening tool along the seam, separating the plastic clips as you go.
Be very gentle whilst prying, and pry only enough to separate the plastic clips—there are several thin points in the midframe bezel that may crack if you bend them too much.
Step 8
- Continue prying around the corner of the phone.
- Slide your opening tool along the seam between the midframe and display along the bottom of the device, releasing more of the plastic clips.
Continue prying around the corner of the phone.
Slide your opening tool along the seam between the midframe and display along the bottom of the device, releasing more of the plastic clips.
Step 9
- Again, pry around the corner, to the power button side.
- Slide the opening tool along the seam.
Again, pry around the corner, to the power button side.
Slide the opening tool along the seam.
Step 10
- Continue sliding the opening tool around the top of the phone, releasing the last of the clips and freeing the midframe from the display assembly.
- At this point, you may want to run your plastic opening tool along the entire perimeter of the device again, to make sure you’ve released all of the plastic clips.
Continue sliding the opening tool around the top of the phone, releasing the last of the clips and freeing the midframe from the display assembly.
At this point, you may want to run your plastic opening tool along the entire perimeter of the device again, to make sure you’ve released all of the plastic clips.
Step 11
- Remove the midframe from the display assembly.
Remove the midframe from the display assembly.
Step 12
Speaker Enclosure
- Hold the midframe in one hand and the speaker enclosure in the other.
- Gently twist the speaker enclosure away from the midframe to pop it free from the clips securing it to the midframe.
- Remove the speaker enclosure from the midframe.
Hold the midframe in one hand and the speaker enclosure in the other.
Gently twist the speaker enclosure away from the midframe to pop it free from the clips securing it to the midframe.
Remove the speaker enclosure from the midframe.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
39 other people completed this guide.
Author
with 5 other contributors
Andrew Optimus Goldheart
Member since: 10/17/2009
491,689 Reputation
411 Guides authored
Badges:
44
+41 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
