Samsung Galaxy S5 Active Front Facing Camera Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          40 minutes

Sections

Rear Case
1 step
SIM Card
1 step
Battery
1 step
Display
7 steps
Front Camera
5 steps

Flags

BackSamsung Galaxy S5 Active
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Case

Insert your fingernail or plastic opening tool into the divot at the top of the rear-facing camera.
Gently pry and twist the flexible rear cover off the back of the phone.

Insert your fingernail or plastic opening tool into the divot at the top of the rear-facing camera.

Gently pry and twist the flexible rear cover off the back of the phone.

1024

Step 2

              SIM Card

Use your fingers to remove the SIM card

Use your fingers to remove the SIM card

Step 3

              Battery

Insert a fingernail or plastic opening tool into the recess in the bottom right corner of the battery and lift upward.
Remove the battery away from the phone.

Insert a fingernail or plastic opening tool into the recess in the bottom right corner of the battery and lift upward.

Remove the battery away from the phone.

Step 4

              Display

Make sure the battery, the SIM card, and the MicroSD card have been removed. If these components are not removed, they may get damaged when the heat is applied.
In this step you’ll be using a heat gun. The heat gun operates at high temperatures, and it may harm you or the device if not used appropriately. Please follow the heat gun safety procedures indicated in it’s manual to prevent any harm.
Use a heat gun at an approximate distance of 2-3 inches from the phone to apply heat to the phone and loosen up the adhesive in the display.

Make sure the battery, the SIM card, and the MicroSD card have been removed. If these components are not removed, they may get damaged when the heat is applied.

In this step you’ll be using a heat gun. The heat gun operates at high temperatures, and it may harm you or the device if not used appropriately. Please follow the heat gun safety procedures indicated in it’s manual to prevent any harm.

Use a heat gun at an approximate distance of 2-3 inches from the phone to apply heat to the phone and loosen up the adhesive in the display.

Step 5

Starting from the upper left corner, insert a guitar pick in between the display and the phone case.

Starting from the upper left corner, insert a guitar pick in between the display and the phone case.

Step 6

Use the pick to pry the display by sliding the pick in the direction shown.
Make sure you pry the display around the edge of the phone. At the bottom of the screen there is a thin metallic strip that connects the display to the motherboard, and it can be easily damaged.
If any resistance is encountered, stop prying and reapply heat to continue prying.

Use the pick to pry the display by sliding the pick in the direction shown.

Make sure you pry the display around the edge of the phone. At the bottom of the screen there is a thin metallic strip that connects the display to the motherboard, and it can be easily damaged.

If any resistance is encountered, stop prying and reapply heat to continue prying.

Step 7

Use the pick to pry the sides and lower part of the display by sliding the pick through the phone.
If any resistance is encountered, stop prying and reapply heat to continue prying.

Use the pick to pry the sides and lower part of the display by sliding the pick through the phone.

Step 8

Using the guitar pick, lift the screen slightly.
You can remove the home button if desired.

Using the guitar pick, lift the screen slightly.

You can remove the home button if desired.

Step 9

Slightly lift, but do not remove, the upper end of display assembly.
Do not remove the front panel entirely. It is still attached by a connector.
If you are reusing the home button flex cable, be careful not to sever the cable from the home button. Adhesive can cause the cable to rip apart from the home button. While the home button will still work, the fingerprint scanner will not.

Slightly lift, but do not remove, the upper end of display assembly.

Do not remove the front panel entirely. It is still attached by a connector.

If you are reusing the home button flex cable, be careful not to sever the cable from the home button. Adhesive can cause the cable to rip apart from the home button. While the home button will still work, the fingerprint scanner will not.

Step 10

Use the sharp tip of a guitar pick to lift the front panel assembly cable connector straight up off its socket on the motherboard.
Safely remove the front panel assembly from phone.

Use the sharp tip of a guitar pick to lift the front panel assembly cable connector straight up off its socket on the motherboard.

Safely remove the front panel assembly from phone.

Step 11

              Front Camera

Use a Phillips 0 screwdriver to remove all 11 Phillips #0 screws.
Make sure you don’t lose them as they are small.

Use a Phillips 0 screwdriver to remove all 11 Phillips #0 screws.

Make sure you don’t lose them as they are small.

Step 12

Push upward from the back side your phone (where the battery should go) to pop out the large gray piece.

Push upward from the back side your phone (where the battery should go) to pop out the large gray piece.

Step 13

You should now have two different pieces. To continue we will only use the piece with the motherboard (Shown on the right side of the picture).

You should now have two different pieces. To continue we will only use the piece with the motherboard (Shown on the right side of the picture).

Step 14

Use your finger or a plastic opening tool to disconnect the front-facing camera from the motherboard.

Use your finger or a plastic opening tool to disconnect the front-facing camera from the motherboard.

Step 15

Use tweezers to gently pull the front-camera out.

Use tweezers to gently pull the front-camera out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 2 other contributors

                    Nils David Corrales Tovar

Member since: 09/22/2014

3,136 Reputation

                                      7 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       USF Tampa, Team 1-5, Hickman Fall 2014                        

                                                  Member of USF Tampa, Team 1-5, Hickman Fall 2014 



                    USFT-HICKMAN-F14S1G5                     


                                            3 Members                     


                                            7 Guides authored

Nortontown - Apr 10, 2015

This is obviously not the front facing camera which is taken out in the end.

Those are the sensors. The camera is still in the upper right corner.

Same goes for the motherboard guide. Front camera is never disconnect nor taken out, this is an issue.

Introduction#

What you need#

Team#

Introduction

What you need

Team