Samsung Galaxy S5 Mini Rear Facing Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Back Cover
1 step
Battery
1 step
Display Assembly
6 steps
Interior Midframe Assembly
4 steps
Motherboard Assembly
2 steps
Rear-Facing Camera
1 step

Flags

BackSamsung Galaxy S5 Mini
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Panel

Insert a fingernail or a plastic opening tool into the slot located above the power button.
Gently pull the panel off the back of the phone.
The plastic snaps will make a popping sound as they separate.

Insert a fingernail or a plastic opening tool into the slot located above the power button.

Gently pull the panel off the back of the phone.

The plastic snaps will make a popping sound as they separate.

1024

Step 2

              Battery

Insert fingernail or plastic opening tool into the slot at the bottom of the battery.
Gently pry the battery away from the phone.
When replacing the battery, ensure the contacts are aligned and press lightly. The battery will appear to fit in multiple directions, so do not force it in.

Insert fingernail or plastic opening tool into the slot at the bottom of the battery.

Gently pry the battery away from the phone.

When replacing the battery, ensure the contacts are aligned and press lightly. The battery will appear to fit in multiple directions, so do not force it in.

Step 3

              Display Assembly

Flip the phone and lay it on a flat surface so that the back is facing towards you.
Use a spudger or plastic opening tool to pry up the home button cable connector and disconnect it.
For reassembly, insert the home button cable connector through the open slot in the display assembly.
Use an iOpener to loosen the adhesive beneath the display.

Flip the phone and lay it on a flat surface so that the back is facing towards you.

Use a spudger or plastic opening tool to pry up the home button cable connector and disconnect it.

For reassembly, insert the home button cable connector through the open slot in the display assembly.

Use an iOpener to loosen the adhesive beneath the display.

Step 4

Flip the phone over so it is lying on its back.
Insert a plastic opening tool or a plastic opening pick in the space between the screen and the frame and slide along the right side of the phone to loosen the adhesive.
Gently lift the display assembly away from the frame until there is a small gap and leave the first opening pick in the bottom right corner next to your home button.
Insert a second opening pick and slide it up to the top left corner of the phone by loosening the adhesive beneath the display.
Do not insert the opening pick more than 1/8 inch. There are some components that can be harmed.

Flip the phone over so it is lying on its back.

Insert a plastic opening tool or a plastic opening pick in the space between the screen and the frame and slide along the right side of the phone to loosen the adhesive.

Gently lift the display assembly away from the frame until there is a small gap and leave the first opening pick in the bottom right corner next to your home button.

Insert a second opening pick and slide it up to the top left corner of the phone by loosening the adhesive beneath the display.

Do not insert the opening pick more than 1/8 inch. There are some components that can be harmed.

Step 5

Reheat the display of your phone with the iOpener. Especially the top and left side of the front.
Insert a third opening pick and slide it carefully to the top left corner of the phone. Be aware of the front camera and the loudspeaker!

Reheat the display of your phone with the iOpener. Especially the top and left side of the front.

Insert a third opening pick and slide it carefully to the top left corner of the phone. Be aware of the front camera and the loudspeaker!

Step 6

Insert a fourth opening pick and slide it to the lower left corner next to your home button.
Flip the opening pick in the top right corner to lift the display. If it is still sticky, move the four opening picks around the frame as you did before to find remains of adhesive.
Do not remove the display assembly from the frame. It is still connected by a cable.

Insert a fourth opening pick and slide it to the lower left corner next to your home button.

Flip the opening pick in the top right corner to lift the display. If it is still sticky, move the four opening picks around the frame as you did before to find remains of adhesive.

Do not remove the display assembly from the frame. It is still connected by a cable.

Step 7

Keep the top portion of the display assembly next to the frame.
Unplug the display flex connector with a spudger.

Keep the top portion of the display assembly next to the frame.

Unplug the display flex connector with a spudger.

Step 8

Use a suction handle to lift the display off of your phone. The home button cable connector should go with the display through a small gap in the mid frame. If it doesn’t, use a tweezer to help a little.
Pull the display assembly away from the phone to remove it.

Use a suction handle to lift the display off of your phone. The home button cable connector should go with the display through a small gap in the mid frame. If it doesn’t, use a tweezer to help a little.

Pull the display assembly away from the phone to remove it.

Step 9

              Interior Midframe Assembly

Remove the 12 4 mm Phillips screws #00 from the midframe.

Remove the 12 4 mm Phillips screws #00 from the midframe.

Step 10

Flip the phone over and lay it on a flat surface so that the back is facing towards you.
Unscrew the 4 mm Phillips #00 screw next to the battery slot.

Flip the phone over and lay it on a flat surface so that the back is facing towards you.

Unscrew the 4 mm Phillips #00 screw next to the battery slot.

Step 11

Circle the midframe with a blow dryer or use the iOpener to loosen the adhesive on the midframe.
Circling the midframe for 10 to 30 seconds with a blowdryer should loosen the adhesive enough.

Circle the midframe with a blow dryer or use the iOpener to loosen the adhesive on the midframe.

Circling the midframe for 10 to 30 seconds with a blowdryer should loosen the adhesive enough.

Step 12

Spread pressure out evenly to avoid damage or bending of the midframe.
Apply pressure to the battery slot on back of the phone to separate the midframes.

Spread pressure out evenly to avoid damage or bending of the midframe.

Apply pressure to the battery slot on back of the phone to separate the midframes.

Step 13

              Motherboard Assembly

Unscrew the 3 mm Phillips #00 screw holding the daughterboard to the motherboard assembly.
Use a plastic opening tool or spudger to pry the daughterboard from its socket.
Use tweezers to pull the cables connecting the daughterboard out from the motherboard.

Unscrew the 3 mm Phillips #00 screw holding the daughterboard to the motherboard assembly.

Use a plastic opening tool or spudger to pry the daughterboard from its socket.

Use tweezers to pull the cables connecting the daughterboard out from the motherboard.

Step 14

Remove the 3 mm Phillips #00 screw holding the motherboard to the frame.
Pull the motherboard from the frame and lay it on a flat surface.

Remove the 3 mm Phillips #00 screw holding the motherboard to the frame.

Pull the motherboard from the frame and lay it on a flat surface.

Step 15

              Rear-Facing Camera

Use a plastic opening tool or spudger to pry off the rear-facing camera from the motherboard.

Use a plastic opening tool or spudger to pry off the rear-facing camera from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Jon Kuzmich

Member since: 09/29/2014

1,963 Reputation

                                      7 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 12-4, Forte Fall 2014                        

                                                  Member of Cal Poly, Team 12-4, Forte Fall 2014 



                    CPSU-FORTE-F14S12G4                     


                                            5 Members                     


                                            38 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team