Difficulty
Moderate
Steps
20
Time Required
50 minutes
Sections
5
- SIM Card
- 2 steps
- Display Assembly
- 8 steps
- Battery
- 5 steps
- Motherboard
- 3 steps
- Front Camera
- 2 steps
Flags
0
BackSamsung Galaxy S6 Active
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SIM Card
- Insert your fingernail or a plastic opening tool into the pivot on the side of the SIM tray.
- Pry open the tray to get it out of the socket.
Insert your fingernail or a plastic opening tool into the pivot on the side of the SIM tray.
Pry open the tray to get it out of the socket.
1024
Step 2
- Remove the SIM tray with SIM card from the phone.
Remove the SIM tray with SIM card from the phone.
Step 3
Display Assembly
- Heat the front face (sides, top, bottom) of the phone with the iOpener, a hair dryer, or a heat gun for 60 seconds to loosen the adhesive around the edge of the glass.
- If using an iOpener, heat it in a microwave for thirty seconds.
Heat the front face (sides, top, bottom) of the phone with the iOpener, a hair dryer, or a heat gun for 60 seconds to loosen the adhesive around the edge of the glass.
If using an iOpener, heat it in a microwave for thirty seconds.
Step 4
- Attach a suction cup to the lower half of the screen.
Attach a suction cup to the lower half of the screen.
Step 5
- Using the suction cup, pull gently the lower half of the panel.
- If you pull too hard you may break the display. If you still feel resistance repeat Step 3, leaving the iOpener on longer.
Using the suction cup, pull gently the lower half of the panel.
If you pull too hard you may break the display. If you still feel resistance repeat Step 3, leaving the iOpener on longer.
Step 6
- Once you’ve opened a large enough gap, insert a plastic tool at the bottom, between the glass and the rest of frame of the phone.
- Slide the plastic opening tool around the screen, prying the display gently away from the body
Once you’ve opened a large enough gap, insert a plastic tool at the bottom, between the glass and the rest of frame of the phone.
Slide the plastic opening tool around the screen, prying the display gently away from the body
Step 7
- Pull the lower half of the screen screen with the suction cup while holding down the frame of the phone to separate both components.
- Only lift the lower part of the screen. It is connected with a clip to the top of the motherboard and can rip off if you pull too hard.
Pull the lower half of the screen screen with the suction cup while holding down the frame of the phone to separate both components.
Only lift the lower part of the screen. It is connected with a clip to the top of the motherboard and can rip off if you pull too hard.
Step 8
- Once the glass is off, you will see a small clip covering the screen connection to the motherboard at the top of the phone. Use tweezers to grab the clip by the crease on its side and pull it out.
Once the glass is off, you will see a small clip covering the screen connection to the motherboard at the top of the phone. Use tweezers to grab the clip by the crease on its side and pull it out.
Step 9
- Undo the screen connection with a plastic tool.
Undo the screen connection with a plastic tool.
Step 10
- Remove the display assembly (LCD and Digitizer).
Remove the display assembly (LCD and Digitizer).
Step 11
Battery
- Use the Phillips Head Screwdriver sized PH000 to remove the sixteen 4mm screws from the frame.
Use the Phillips Head Screwdriver sized PH000 to remove the sixteen 4mm screws from the frame.
Step 12
- Put a little pressure on the top, on the bottom, and on the sides of the phone to separate the rear case.
- You will hear the clips start undoing themselves.
Put a little pressure on the top, on the bottom, and on the sides of the phone to separate the rear case.
You will hear the clips start undoing themselves.
Step 13
- Once all the clips have popped, pull out the rear case to separate it from the frame with the battery.
- The battery will be on the back side of this frame.
Once all the clips have popped, pull out the rear case to separate it from the frame with the battery.
The battery will be on the back side of this frame.
Step 14
- Insert a plastic opening tool on the side of the frame and pull out the battery.
Insert a plastic opening tool on the side of the frame and pull out the battery.
Step 15
- Remove the battery from the frame.
Remove the battery from the frame.
Step 16
Motherboard
- Use a plastic tool to undo all the connections in the motherboard.
- There are three connections that have to be removed.
Use a plastic tool to undo all the connections in the motherboard.
There are three connections that have to be removed.
Step 17
- Insert the flats end of the spudger below the motherboard and twist it to pry the board up.
Insert the flats end of the spudger below the motherboard and twist it to pry the board up.
Step 18
- Remove the motherboard from the rear case.
Remove the motherboard from the rear case.
Step 19
Front Camera
- The front camera will be attached to the back of the motherboard.
- Turn the motherboard around and use a plastic tool to undo the connection of the front camera.
The front camera will be attached to the back of the motherboard.
Turn the motherboard around and use a plastic tool to undo the connection of the front camera.
Step 20
- Use the tweezers to remove the front camera from the motherboard.
Use the tweezers to remove the front camera from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Lucia Valbuena
Member since: 02/15/2017
2,412 Reputation
8 Guides authored
Badges:
18
+15 more badges
Team
USF Tampa, Team 1-5, Sullivan Spring 2017
Member of USF Tampa, Team 1-5, Sullivan Spring 2017
USFT-SULLIVAN-S17S1G5
3 Members
25 Guides authored
