Difficulty

Moderate

Steps

17

Time Required

                          10 - 25 minutes

Sections

4

  • Samsung Galaxy S7 Active Disassembly
  • 4 steps
  • Battery
  • 8 steps
  • Rear Camera
  • 1 step
  • Motherboard
  • 4 steps

Flags

1

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackSamsung Galaxy S7 Active

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Samsung Galaxy S7 Active Disassembly
  • Melt the adhesive on the screen by applying a blow dryer directly on the screen.
  • Your phone is hot, please do not touch it with your bare hand.

Melt the adhesive on the screen by applying a blow dryer directly on the screen.

Your phone is hot, please do not touch it with your bare hand.

1024

Step 2

  • Wedge the metal spudger in between the screen and the frame to begin separating them.
  • It would be easier to separate the screen from the sealing adhesive on the frame if you with more than one metal spudger.
  • Your phone might no longer be watertight after you reassemble it.

Wedge the metal spudger in between the screen and the frame to begin separating them.

It would be easier to separate the screen from the sealing adhesive on the frame if you with more than one metal spudger.

Your phone might no longer be watertight after you reassemble it.

Step 3

  • Slide the metal spudger around the phone at least once.
  • It would be easier to slide your metal spudger if you apply the blow dryer to where you are currently sliding.

Slide the metal spudger around the phone at least once.

It would be easier to slide your metal spudger if you apply the blow dryer to where you are currently sliding.

Step 4

  • Lift the screen up with your hands.
  • Please wash your hands thoroughly with hot water and soap after you finish.

Lift the screen up with your hands.

Please wash your hands thoroughly with hot water and soap after you finish.

Step 5

              Battery
  • Use a Phillips #000 screwdriver to remove a single screw.

Use a Phillips #000 screwdriver to remove a single screw.

Step 6

  • Use tweezers to remove the small plastic cover you just unscrewed.

Use tweezers to remove the small plastic cover you just unscrewed.

Step 7

  • Use tweezers to remove the other small plastic cover.

Use tweezers to remove the other small plastic cover.

Step 8

  • Use a Phillips head #000 to take out the eleven screws marked in the photo.

Use a Phillips head #000 to take out the eleven screws marked in the photo.

Step 9

  • Use tweezers to disconnect the marked pieces from the motherboard.

Use tweezers to disconnect the marked pieces from the motherboard.

Step 10

  • Use tweezers to take out the middle button and its connection to the motherboard.

Use tweezers to take out the middle button and its connection to the motherboard.

Step 11

  • Use a metal spudger to pull the mid frame and battery off of the motherboard.

Use a metal spudger to pull the mid frame and battery off of the motherboard.

Step 12

  • Use a spudger to remove the battery from the midframe.
  • To install a new battery and adhesive, follow this guide.

Use a spudger to remove the battery from the midframe.

To install a new battery and adhesive, follow this guide.

Step 13

              Rear Camera
  • Use tweezers to disconnect the front camera from the battery.
  • The connector should unsnap similar to a lego piece.

Use tweezers to disconnect the front camera from the battery.

The connector should unsnap similar to a lego piece.

Step 14

              Motherboard
  • Use a Phillips 000 screwdriver to remove the screw covering the proximity sensor.

Use a Phillips 000 screwdriver to remove the screw covering the proximity sensor.

Step 15

  • Use tweezers to remove the proximity sensor.
  • Set this aside for now.

Use tweezers to remove the proximity sensor.

Set this aside for now.

Step 16

  • Use tweezers to disconnect the front mic and the two cables that have been marked in the photo.

Use tweezers to disconnect the front mic and the two cables that have been marked in the photo.

Step 17

  • Use your hands and a metal spudger to lift the motherboard out of the phone.
  • Be gentle, as there is still a connection on the underside of the motherboard.
  • Use a metal spudger to remove this connection.

Use your hands and a metal spudger to lift the motherboard out of the phone.

Be gentle, as there is still a connection on the underside of the motherboard.

Use a metal spudger to remove this connection.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors 


                    Joe De Leone

Member since: 04/18/2018

310 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team S18-G1, Livingston Spring 2018                        

                                                  Member of Cal Poly, Team S18-G1, Livingston Spring 2018 



                    CPSU-LIVINGSTON-S18S18G1                     


                                            4 Members                     


                                            15 Guides authored