Samsung Galaxy S8 Active Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 minutes

Sections

SIM Tray/Card
1 step
NFC Antenna and Charging Coil Assembly
7 steps
Loudspeaker Assembly
1 step
Display
5 steps

Flags

BackSamsung Galaxy S8 Active
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

This guide involves removing the back cover of the device, so you will need replacement adhesive to reattach the back cover to the phone.

Before disassembling your device, be sure the battery is charged below 25%. If accidentally punctured or damaged, the battery can catch fire and/or explode; if discharged below 25%, the chances of fire/explosion is decreased.

Follow the iOpener Heating guide for instructions on using the iOpener.

What you need

Step 1

              SIM Tray/Card

Insert and gently push the SIM card ejector tool (or an unfolded paperclip) into the small hole on the left side of the top edge of the phone.
Press gently to eject the SIM tray.
Remove the SIM card tray from the device.
To reinsert the SIM card tray, orient the SIM card with the gold contacts facing up and the notch to the bottom right. Reinsert the SIM card by pressing the card gently into the SIM tray slot.

Insert and gently push the SIM card ejector tool (or an unfolded paperclip) into the small hole on the left side of the top edge of the phone.

Press gently to eject the SIM tray.

Remove the SIM card tray from the device.

To reinsert the SIM card tray, orient the SIM card with the gold contacts facing up and the notch to the bottom right. Reinsert the SIM card by pressing the card gently into the SIM tray slot.

1024

Step 2

              NFC Antenna and Charging Coil Assembly

Removing the back cover of the S8 Active will compromise its waterproof seals. Have replacement adhesive on hand before you proceed, or be sure to avoid exposure to liquid if you do not replace the adhesive when you reassemble the device.
Remove four black 3mm screws from the outside edges of the device that hold the rubber bumpers in place using the TR6 Torx Security Screwdriver.
Take off the rubber bumpers from the top and bottom edges of the device.

Removing the back cover of the S8 Active will compromise its waterproof seals. Have replacement adhesive on hand before you proceed, or be sure to avoid exposure to liquid if you do not replace the adhesive when you reassemble the device.

Remove four black 3mm screws from the outside edges of the device that hold the rubber bumpers in place using the TR6 Torx Security Screwdriver.

Take off the rubber bumpers from the top and bottom edges of the device.

Step 3

Use a heat gun to lightly heat the edges of the back to soften the adhesive that connects the back cover to the rest of the frame.
An iFixit iOpener, hair dryer, or hot plate can also be used to heat the edges.
Using a heat gun, hair dryer, or hot plate will make the metal frame rather hot to the touch, so handle it with care.
Be careful not to overheat the device –the OLED display, battery and other internal parts can be damaged by excessive heat. Approximately one minute should be enough to soften the adhesive.

Use a heat gun to lightly heat the edges of the back to soften the adhesive that connects the back cover to the rest of the frame.

An iFixit iOpener, hair dryer, or hot plate can also be used to heat the edges.

Using a heat gun, hair dryer, or hot plate will make the metal frame rather hot to the touch, so handle it with care.

Be careful not to overheat the device –the OLED display, battery and other internal parts can be damaged by excessive heat. Approximately one minute should be enough to soften the adhesive.

Step 4

Insert the Jimmy tool under the edge of the back cover.
Because of the texture of the back cover, a suction handle does not provide any grip to help lift the back cover.
Once the Jimmy tool is under the edge of the cover, insert an opening pick into the seam to prevent the seam from closing if the Jimmy tool slips or is accidentally removed.
Cut slowly around the top section of the device and be careful to avoid damaging the cables for the fingerprint sensor and camera. Avoid prying too far into the top of the device to protect the fingerprint sensor.
Slide the Jimmy tool down the sides of the device, separating the adhesive.

Insert the Jimmy tool under the edge of the back cover.

Because of the texture of the back cover, a suction handle does not provide any grip to help lift the back cover.

Once the Jimmy tool is under the edge of the cover, insert an opening pick into the seam to prevent the seam from closing if the Jimmy tool slips or is accidentally removed.

Cut slowly around the top section of the device and be careful to avoid damaging the cables for the fingerprint sensor and camera. Avoid prying too far into the top of the device to protect the fingerprint sensor.

Slide the Jimmy tool down the sides of the device, separating the adhesive.

Step 5

Use the opening pick to slice through any remaining adhesive.
If you have replacement adhesive strips, remove any remaining adhesive from the device frame using the Jimmy tool.
Open the back cover slightly to the point that you can see the fingerprint sensor flex cable connector.
The fingerprint sensor cable connects towards the top of the phone near the front-facing camera. To avoid tearing the cable, pull the back cover off gently.

Use the opening pick to slice through any remaining adhesive.

If you have replacement adhesive strips, remove any remaining adhesive from the device frame using the Jimmy tool.

Open the back cover slightly to the point that you can see the fingerprint sensor flex cable connector.

The fingerprint sensor cable connects towards the top of the phone near the front-facing camera. To avoid tearing the cable, pull the back cover off gently.

Step 6

Slowly flip the cover over and set it down on top of the rest of the device.
Disconnect the fingerprint flex cable using the flat end of a spudger.
Remove the back cover.
To reconnect the fingerprint sensor cable during reassembly, angle the back cover until the flex cable lines up over its socket. Use the flat end of a spudger to snap the cable in place by gently pressing straight down.

Slowly flip the cover over and set it down on top of the rest of the device.

Disconnect the fingerprint flex cable using the flat end of a spudger.

Remove the back cover.

To reconnect the fingerprint sensor cable during reassembly, angle the back cover until the flex cable lines up over its socket. Use the flat end of a spudger to snap the cable in place by gently pressing straight down.

Step 7

Remove eleven 3.5 mm screws using a Phillips #00 Screwdriver.
Remove two 2mm screws using a Phillips #00 Screwdriver.

Remove eleven 3.5 mm screws using a Phillips #00 Screwdriver.

Remove two 2mm screws using a Phillips #00 Screwdriver.

Step 8

Remove the NFC antenna and charging coil assembly using the flat end of a spudger.

Remove the NFC antenna and charging coil assembly using the flat end of a spudger.

Step 9

              Loudspeaker Assembly

Remove the loudspeaker assembly using the flat end of a spudger.

Remove the loudspeaker assembly using the flat end of a spudger.

Step 10

              Display

Disconnect the display flex cable on the motherboard using the flat end of a spudger.

Disconnect the display flex cable on the motherboard using the flat end of a spudger.

Step 11

Place the clear side of a heated iOpener over each edge of the phone for about 90 seconds to soften the adhesive attached to the display.
Reheat iOpener as needed.
A hair dryer or heat gun can also be used to soften the adhesive. A hair dryer/heat gun will make the metal frame hot to the touch, so handle it with care.

Place the clear side of a heated iOpener over each edge of the phone for about 90 seconds to soften the adhesive attached to the display.

Reheat iOpener as needed.

A hair dryer or heat gun can also be used to soften the adhesive. A hair dryer/heat gun will make the metal frame hot to the touch, so handle it with care.

Step 12

Press a suction handle in the middle of the bottom half of the display.
Pull up on the suction cup until there is a small gap in between the display and the frame.
If your display is cracked, the suction cup will still pull up the display as one piece.

Press a suction handle in the middle of the bottom half of the display.

Pull up on the suction cup until there is a small gap in between the display and the frame.

If your display is cracked, the suction cup will still pull up the display as one piece.

Step 13

Insert an opening pick into the gap between the display and the frame created by pulling up on the suction cup.

Insert an opening pick into the gap between the display and the frame created by pulling up on the suction cup.

Step 14

With the opening pick, continue slicing through the adhesive around the edge of the phone.
Once all of the adhesive is separated, remove the display by pulling up on the suction handle.

With the opening pick, continue slicing through the adhesive around the edge of the phone.

Once all of the adhesive is separated, remove the display by pulling up on the suction handle.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 2 other contributors

                    Erik Mauk

Member since: 01/24/2019

1,396 Reputation

                                      6 Guides authored                  



                       Badges:
                       12





                                                        +9 more badges

Team

                       Cal Poly, Team S2-G1, White Winter 2019                        

                                                  Member of Cal Poly, Team S2-G1, White Winter 2019 



                    CPSU-WHITE-W19S2G1                     


                                            3 Members                     


                                            11 Guides authored

jjustin127 - Jan 25, 2020

adding where to and how much of the adhesive to use when putting screen and back panel back on would be a great addition to this guide

Introduction#

What you need#

Team#

Introduction

What you need

Team