Difficulty
Moderate
Steps
10
Time Required
15 minutes
Sections
2
- Back Panel
- 6 steps
- Battery
- 4 steps
Flags
1
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
BackSamsung Galaxy Tab 10.1 4G
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Power off your tablet before you begin disassembly.
- Screen side facing you, rotate device 180 degrees so the “SAMSUNG” logo is upside down.
Power off your tablet before you begin disassembly.
Screen side facing you, rotate device 180 degrees so the “SAMSUNG” logo is upside down.
1024
Step 2
- Using the plastic opening tool, start in the center near the charge port and wedge the angled tip between the plastic back and the glass screen.
- Create a wedge and apply pressure. Use the tool to separate the screen from the back until you hear an audible “pop."
- Continue to wedge the tool about every inch along the current edge.
Using the plastic opening tool, start in the center near the charge port and wedge the angled tip between the plastic back and the glass screen.
Create a wedge and apply pressure. Use the tool to separate the screen from the back until you hear an audible “pop."
Continue to wedge the tool about every inch along the current edge.
Step 3
- Once the bottom edge has been loosened, work towards a bottom corner from the other edge and continue to wedge gently until you can “pop” the corner out.
- Continue this process on the other bottom corner until it can be popped out as well.
Once the bottom edge has been loosened, work towards a bottom corner from the other edge and continue to wedge gently until you can “pop” the corner out.
Continue this process on the other bottom corner until it can be popped out as well.
Step 4
- Place your hand between the device and the back panel. Then continue the wedging motion along the top edge of the device until the back panel comes loose.
- Do not wedge the tool directly on top of the power buttons and headphone jack. Wedge nearby so that you don’t damage internal hardware.
Place your hand between the device and the back panel. Then continue the wedging motion along the top edge of the device until the back panel comes loose.
Do not wedge the tool directly on top of the power buttons and headphone jack. Wedge nearby so that you don’t damage internal hardware.
Step 5
- Remove the back from the device.
- Excessive force shouldn’t be necessary here. If the back panel is sticking, find the area of the edge closest to the sticking point and wedge the opening tool there until the back panel pops free.
Remove the back from the device.
Excessive force shouldn’t be necessary here. If the back panel is sticking, find the area of the edge closest to the sticking point and wedge the opening tool there until the back panel pops free.
Step 6
- When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.
- The connection between the battery and motherboard is a group of four wires in black housing that can be found near the top middle of the device. Using a plastic spudger or a flat, slim tool, lift the black connector housing upwards to disconnect it.
When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.
The connection between the battery and motherboard is a group of four wires in black housing that can be found near the top middle of the device. Using a plastic spudger or a flat, slim tool, lift the black connector housing upwards to disconnect it.
Step 7
Battery
- Remove the small piece of tape covering the ribbon connector.
- You don’t need to save this piece of tape.
- When reassembling your device, simply replace this tape with a piece of scotch tape.
Remove the small piece of tape covering the ribbon connector.
You don’t need to save this piece of tape.
When reassembling your device, simply replace this tape with a piece of scotch tape.
Step 8
- Carefully slide a plastic spudger under the black strip of plastic on the far side of the ribbon connector housing.
- When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.
- Lift the black strip upwards. This will release the ribbon.
- Slide the ribbon out of the connector.
- Repeat this step to release the other two ribbons.
- You will need to remove the tape from covering those connectors, too.
Carefully slide a plastic spudger under the black strip of plastic on the far side of the ribbon connector housing.
When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.
Lift the black strip upwards. This will release the ribbon.
Slide the ribbon out of the connector.
Repeat this step to release the other two ribbons.
You will need to remove the tape from covering those connectors, too.
Step 9
- Use the Phillips #00 screwdriver to unscrew the 10 3mm screws holding the battery in place.
Use the Phillips #00 screwdriver to unscrew the 10 3mm screws holding the battery in place.
Step 10
- Lift the battery out of its housing to remove it.
Lift the battery out of its housing to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
7 other people completed this guide.
Author
with 3 other contributors
Ashley Stark
Member since: 09/23/2015
1,202 Reputation
6 Guides authored
Badges:
15
+12 more badges
Team
Baylor, Team 10-11, Williams Fall 2015
Member of Baylor, Team 10-11, Williams Fall 2015
BU-WILLIAMS-F15S10G11
3 Members
16 Guides authored
