Difficulty
Moderate
Steps
8
Time Required
35 minutes
Sections
3
- Rear Panel
- 3 steps
- Battery
- 3 steps
- Front Facing Camera
- 2 steps
Flags
0
BackSamsung Galaxy Tab 10.1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Panel
- Place the bottom of the tablet towards you.
- Remove the 4.1mm screws near the charge port with a Tri-Wing screwdriver.
- If there are plastic tabs covering these screws, use pointed tweezers to pry the tabs out.
- On model GT-P7500, this step is omitted, as that model doesn’t have these 2 screws.
Place the bottom of the tablet towards you.
Remove the 4.1mm screws near the charge port with a Tri-Wing screwdriver.
If there are plastic tabs covering these screws, use pointed tweezers to pry the tabs out.
On model GT-P7500, this step is omitted, as that model doesn’t have these 2 screws.
1024
Step 2
- Start in the middle of the left side and insert a plastic opening tool between the rear panel and the front panel assembly.
- Carefully run the plastic opening tool along the left and top edge to pry the rear panel away from the rest of the device.
- Place opening picks along the side you have already pried open to keep the back panel detached from the rest of the device.
- Be sure to work carefully, as prying too firmly can crack the screen.
Start in the middle of the left side and insert a plastic opening tool between the rear panel and the front panel assembly.
Carefully run the plastic opening tool along the left and top edge to pry the rear panel away from the rest of the device.
Place opening picks along the side you have already pried open to keep the back panel detached from the rest of the device.
Be sure to work carefully, as prying too firmly can crack the screen.
Step 3
- Using the plastic opening tools, continue to carefully run along the right and bottom edge, and then lift the screen from the back panel.
Using the plastic opening tools, continue to carefully run along the right and bottom edge, and then lift the screen from the back panel.
Step 4
Battery
- Flip up the retaining flaps on the ZIF connectors that secure the three large ribbon cables.
- Carefully pull the three ribbon cables from their sockets on the motherboard.
Flip up the retaining flaps on the ZIF connectors that secure the three large ribbon cables.
Carefully pull the three ribbon cables from their sockets on the motherboard.
Step 5
- Remove the ten 3 mm Phillips #00 screws surrounding the battery.
Remove the ten 3 mm Phillips #00 screws surrounding the battery.
Step 6
- Lift the edge of the battery up with your finger or a spudger.
- Detach the battery by holding the motherboard down while gently lifting the battery up.
Lift the edge of the battery up with your finger or a spudger.
Detach the battery by holding the motherboard down while gently lifting the battery up.
Step 7
Front Facing Camera
- Use the spudger to pry up on orange connection. This is the connection to the front facing camera.
Use the spudger to pry up on orange connection. This is the connection to the front facing camera.
Step 8
- Grab the orange connection with your fingers and lift it up from its slot.
- We have removed the motherboard in these pictures to make it easier to see, but it is not necessary to complete this step.
Grab the orange connection with your fingers and lift it up from its slot.
We have removed the motherboard in these pictures to make it easier to see, but it is not necessary to complete this step.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 5 other contributors
Davie Sy
Member since: 09/30/2013
1,421 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team 13-5, Forte Fall 2013
Member of Cal Poly, Team 13-5, Forte Fall 2013
CPSU-FORTE-F13S13G5
5 Members
17 Guides authored
