Samsung Galaxy Tab 4 10 1 Lcd Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Battery
6 steps
Digitizer
4 steps
LCD Display
3 steps

Flags

BackSamsung Galaxy Tab 4 10.1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Insert the wedge of the nylon spudger and slide it between the front and back panels until the back comes off.

Insert the wedge of the nylon spudger and slide it between the front and back panels until the back comes off.

1024

Step 2

Peel off the green tape that covers the connectors for the three black strips.
Use the tip of a spudger or your fingernail to flip up the small retaining flaps.

Peel off the green tape that covers the connectors for the three black strips.

Use the tip of a spudger or your fingernail to flip up the small retaining flaps.

Step 3

Use a Phillips #00 screwdriver to remove the four 3.2mm screws.

Use a Phillips #00 screwdriver to remove the four 3.2mm screws.

Step 4

Detach the red, blue, and black cables by prying up on the white connector from the motherboard.
If using fingers instead, pull evenly on the full width of the cable so the wires are not overly strained.
If you pull too hard you can damage the connector on the circuit board. Use a spudger or tweezers to push down on the black connector on the board while gently prying the battery connector loose. The connector breaks VERY easily.

Detach the red, blue, and black cables by prying up on the white connector from the motherboard.

If using fingers instead, pull evenly on the full width of the cable so the wires are not overly strained.

If you pull too hard you can damage the connector on the circuit board. Use a spudger or tweezers to push down on the black connector on the board while gently prying the battery connector loose. The connector breaks VERY easily.

Step 5

Use the nylon spudger to remove the battery by prying up on the edges.

Use the nylon spudger to remove the battery by prying up on the edges.

Step 6

Once the battery is loose, lift it out of the device.

Once the battery is loose, lift it out of the device.

Step 7

              Digitizer

Use the flat end of a spudger to disconnect the home button.

Use the flat end of a spudger to disconnect the home button.

Step 8

Use an iOpener to weaken the adhesive around the display.

Use an iOpener to weaken the adhesive around the display.

Step 9

Wedge an opening pick between the digitizer and display frame.
Slide the opening pick around the perimeter to separate the two pieces.

Wedge an opening pick between the digitizer and display frame.

Slide the opening pick around the perimeter to separate the two pieces.

Step 10

Lift and remove the digitizer.

Lift and remove the digitizer.

Step 11

              LCD Display

Use a spudger to flip up the small locking flap on the display ZIF connector.
Remove the display ribbon cable.

Use a spudger to flip up the small locking flap on the display ZIF connector.

Remove the display ribbon cable.

Step 12

Hold the frame with both hands and push the LCD display up from underneath with your fingers.

Hold the frame with both hands and push the LCD display up from underneath with your fingers.

Step 13

Remove the LCD display.

Remove the LCD display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                    Blake Klein

Member since: 01/29/2017

66,666 Reputation

                                      54 Guides authored                  



                       Badges:
                       43







                                                        +40 more badges

Introduction#

What you need#

Introduction

What you need