Samsung Galaxy Tab 7 0 Sprint Audio Jack Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          45 minutes - 1 hour

Sections

Front Panel
6 steps
Battery
2 steps
Audio Jack
2 steps

Flags

BackSamsung Galaxy Tab 7.0 Sprint
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front Panel

Fully power off the device.
Disconnect and remove any cables that are connected to the device (i.e. chargers or headphones).
Place the device on a flat, stable, and clean surface.

Fully power off the device.

Disconnect and remove any cables that are connected to the device (i.e. chargers or headphones).

Place the device on a flat, stable, and clean surface.

1024

Step 2

Remove the plastic tabs on the bottom of the device using the metal spudger, as shown in the pictures.
Make sure you have a place to store small parts like this where they are easily accessible but hard to lose.

Remove the plastic tabs on the bottom of the device using the metal spudger, as shown in the pictures.

Make sure you have a place to store small parts like this where they are easily accessible but hard to lose.

Step 3

Using a Tri-Point YO Screwdriver, remove the two 4.1mm Tri-Wing screws.
Place the removed screws in a location similar to where you placed the pads that you removed in the previous step.

Using a Tri-Point YO Screwdriver, remove the two 4.1mm Tri-Wing screws.

Place the removed screws in a location similar to where you placed the pads that you removed in the previous step.

Step 4

Wedge a plastic opening tool between the front and back panel, on the bottom right corner.
Slowly push the tool down to make a small gap between the front panel and the back panel.
Holding the tool steady, run the tool along the bottom part of the device from right to left. This will make the gap between the front panel and the back panel bigger.
When wedging your tool into the device, make sure to apply the pressure to the screen and device at a slow but steady speed to the screen. Too much pressure too fast can crack the screen.

Wedge a plastic opening tool between the front and back panel, on the bottom right corner.

Slowly push the tool down to make a small gap between the front panel and the back panel.

Holding the tool steady, run the tool along the bottom part of the device from right to left. This will make the gap between the front panel and the back panel bigger.

When wedging your tool into the device, make sure to apply the pressure to the screen and device at a slow but steady speed to the screen. Too much pressure too fast can crack the screen.

Step 5

Leave the previously used tool wedged in the device.
Insert another plastic opening tool into the bottom of the left side, as shown.
Using a similar procedure to the last step, run the tool along the side and widen the front panel-back panel gap. This time, run the device from bottom to top.
Repeat this process for the right side of the device, starting at the bottom of the right side.
Some of the other tools that you wedged in may pop out. Simply wedge them back in where they were previously, and continue.

Leave the previously used tool wedged in the device.

Insert another plastic opening tool into the bottom of the left side, as shown.

Using a similar procedure to the last step, run the tool along the side and widen the front panel-back panel gap. This time, run the device from bottom to top.

Repeat this process for the right side of the device, starting at the bottom of the right side.

Some of the other tools that you wedged in may pop out. Simply wedge them back in where they were previously, and continue.

Step 6

Holding the bottom of the device, lift the front panel from the back panel.
Make sure to remove the front panel slowly, to ensure that you don’t accidentally break anything.

Holding the bottom of the device, lift the front panel from the back panel.

Make sure to remove the front panel slowly, to ensure that you don’t accidentally break anything.

Step 7

              Battery

Place the front panel on the table, with the battery facing up.
Find the small screw that is holding the battery to the motherboard, and unscrew it using the Phillips #00 Screwdriver.
Make sure to keep track of the screw for when you reassemble the device.

Place the front panel on the table, with the battery facing up.

Find the small screw that is holding the battery to the motherboard, and unscrew it using the Phillips #00 Screwdriver.

Make sure to keep track of the screw for when you reassemble the device.

Step 8

Lift the bottom part of the battery.
Use a plastic opening tool to remove the battery connector from its place on the motherboard. Make sure to pull it straight up.
Do not poke the battery with a screwdriver or an opening tool.

Lift the bottom part of the battery.

Use a plastic opening tool to remove the battery connector from its place on the motherboard. Make sure to pull it straight up.

Do not poke the battery with a screwdriver or an opening tool.

Step 9

              Audio Jack

With the plastic opening tool, disconnect the following 5 connectors:
Headphone jack/microphone cable
Volume control cable
Touchscreen cable
Control button LED cable
Display data cable
Use the Phillips #00 screwdriver to remove the seven screws holding down the motherboard.
Carefully lift the motherboard away from the rear panel.

With the plastic opening tool, disconnect the following 5 connectors:

Headphone jack/microphone cable

Volume control cable

Touchscreen cable

Control button LED cable

Display data cable

Use the Phillips #00 screwdriver to remove the seven screws holding down the motherboard.

Carefully lift the motherboard away from the rear panel.

Step 10

Using the Phillips #00 screwdriver, unscrew the panel that secures the audio jack to the rear panel.
After lifting the audio jack off the adhesive, remove it from the device.

Using the Phillips #00 screwdriver, unscrew the panel that secures the audio jack to the rear panel.

After lifting the audio jack off the adhesive, remove it from the device.

To reassemble your device, follow these instructions in reverse order. Make sure all parts are aligned properly before attempting to put them back together.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Peter Van Ausdeln

Member since: 01/19/2017

606 Reputation

                                      6 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UC Davis, Team 1-2, Rodger Winter 2017                        

                                                  Member of UC Davis, Team 1-2, Rodger Winter 2017 



                    UCD-RODGER-W17S1G2                     


                                            4 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team