Difficulty
Moderate
Steps
12
Time Required
15 - 45 minutes
Sections
6
- Back Panel
- 1 step
- Back Camera
- 1 step
- Front Camera
- 1 step
- Motherboard
- 6 steps
- Battery
- 1 step
- Screen
- 2 steps
Flags
1
Scenic Route
This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.
BackSamsung Galaxy Tab E 8.0
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Use the iFixit Opening Tool to pry off the back case, moving the tool around the screen.
- Make sure the device is off and the SD card is removed before taking off the back casing.
Use the iFixit Opening Tool to pry off the back case, moving the tool around the screen.
Make sure the device is off and the SD card is removed before taking off the back casing.
1024
Step 2
Back Camera
- Use the tweezers to lift the switch connecting the back camera to the motherboard.
- Use your hand to remove the back camera from the motherboard.
Use the tweezers to lift the switch connecting the back camera to the motherboard.
Use your hand to remove the back camera from the motherboard.
Step 3
Front Camera
- Use the tweezers to lift the switch connecting the front camera to the motherboard.
- Remove the front camera from the motherboard by lifting with the tweezers.
Use the tweezers to lift the switch connecting the front camera to the motherboard.
Remove the front camera from the motherboard by lifting with the tweezers.
Step 4
Motherboard
- Use the tweezers to flip the switch on the bottom of the strap that goes over the battery.
- Release the strap from the switch by lifting the strap with your hand.
Use the tweezers to flip the switch on the bottom of the strap that goes over the battery.
Release the strap from the switch by lifting the strap with your hand.
Step 5
- Use the tweezers to flip the switch that connects the top of the strap to the motherboard.
- Lift the top end of the strap with your hand and remove the strap completely from the device.
Use the tweezers to flip the switch that connects the top of the strap to the motherboard.
Lift the top end of the strap with your hand and remove the strap completely from the device.
Step 6
- Use the tweezers to flip the switch of the connector.
- Lift the connector from the motherboard.
- This connector does not come completely off, but disconnects from the motherboard.
Use the tweezers to flip the switch of the connector.
Lift the connector from the motherboard.
This connector does not come completely off, but disconnects from the motherboard.
Step 7
- Use the tweezers to flip the switch of the blue connector on the motherboard.
- Lift the connector from the motherboard.
- This switch can detach from the device, but just needs to disconnect from the motherboard.
- Ensure the blue ribbon cable is not under the motherboard upon reassembly.
Use the tweezers to flip the switch of the blue connector on the motherboard.
This switch can detach from the device, but just needs to disconnect from the motherboard.
Ensure the blue ribbon cable is not under the motherboard upon reassembly.
Step 8
- Use the tweezers to flip the switch of the connector that runs from the battery to the motherboard.
- Lift the connector from the motherboard.
- This switch can detach from the device, but just needs to disconnect from the motherboard.
Use the tweezers to flip the switch of the connector that runs from the battery to the motherboard.
This switch can detach from the device, but just needs to disconnect from the motherboard.
Step 9
- Use a JIS #00 screwdriver to remove the six 4.5mm screws at the top of the motherboard.
- Lift the motherboard with your hand to detach the motherboard from the device.
Use a JIS #00 screwdriver to remove the six 4.5mm screws at the top of the motherboard.
Lift the motherboard with your hand to detach the motherboard from the device.
Step 10
Battery
- Use the tweezers to lift the flap on the left end of the battery and pull up with your hand to remove the battery.
- The battery is held by an adhesive on the back, so it will take some force to remove.
Use the tweezers to lift the flap on the left end of the battery and pull up with your hand to remove the battery.
The battery is held by an adhesive on the back, so it will take some force to remove.
Step 11
Screen
- Use an iOpener or a heat gun/hair dryer to warm the outer 1/2 inch of the screen. It should be very warm but not too hot to touch or you may cause heat damage to components inside the device.
- Use the iFixit Opening Tool to get between the plastic screen and the device to pry off the screen.
- The metal spudger may be needed to get between the screen.
- The metal spudger may cause more damage to the screen if used with force.
Use an iOpener or a heat gun/hair dryer to warm the outer 1/2 inch of the screen. It should be very warm but not too hot to touch or you may cause heat damage to components inside the device.
Use the iFixit Opening Tool to get between the plastic screen and the device to pry off the screen.
The metal spudger may be needed to get between the screen.
The metal spudger may cause more damage to the screen if used with force.
Step 12
- Use the metal spudger to get between the device and the internal screen.
- Pry out the screen from the device.
Use the metal spudger to get between the device and the internal screen.
Pry out the screen from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 5 other contributors
Christian Bloemhof
Member since: 10/08/2018
1,039 Reputation
7 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team S13-G4, White Fall 2018
Member of Cal Poly, Team S13-G4, White Fall 2018
CPSU-WHITE-F18S13G4
4 Members
8 Guides authored
George Tedrick - Jan 25, 2019
Reply
I am working on a 7” lite E. Is the procedure about the same?
