Samsung Galaxy Tab E 9 6 Verizon Front Panel Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 minutes

Sections

Back Casing
3 steps
Front Panel
3 steps

Flags

BackSamsung Galaxy Tab E 9.6 Verizon
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Casing

Remove any micro-SD or SIM cards before continuing.
Verify your device is turned OFF.
Disconnect all external devices from your tablet.

Remove any micro-SD or SIM cards before continuing.

Verify your device is turned OFF.

Disconnect all external devices from your tablet.

1024

Step 2

Insert the plastic opening tool by wedging it between the device’s screen and back cover.
Move the plastic tool around the edges of the device to undo the plastic lips holding the casing together.
This step may require more force than expected. If difficult, try using a suction cup on the screen.

Insert the plastic opening tool by wedging it between the device’s screen and back cover.

Move the plastic tool around the edges of the device to undo the plastic lips holding the casing together.

This step may require more force than expected. If difficult, try using a suction cup on the screen.

Step 3

This process will become easier as more clips are separated.
Use your hands to gently pull the back cover off the device after about half of the clips are separated.
A suction cup can be used in this step as well to assist in pulling the device apart.

This process will become easier as more clips are separated.

Use your hands to gently pull the back cover off the device after about half of the clips are separated.

A suction cup can be used in this step as well to assist in pulling the device apart.

Step 4

              Front Panel

Turn the device over so the screen is facing down. Locate the front panel assembly connector at the top left corner of the motherboard.
To remove the connector, first use a pair of tweezers and flip the connector lock upwards towards the battery.

Turn the device over so the screen is facing down. Locate the front panel assembly connector at the top left corner of the motherboard.

To remove the connector, first use a pair of tweezers and flip the connector lock upwards towards the battery.

Step 5

Once you’ve undone the connector lock, use a pair of tweezers to pull the cable front its housing.

Once you’ve undone the connector lock, use a pair of tweezers to pull the cable front its housing.

Step 6

Turn the device back over and use a plastic opening tool to detach the adhesive glue securing the front casing.
You will need to wedge a plastic opening tool in between the front casing and the screen. Then move the tool around the perimeter of the device to break the adhesive.
Once you’ve loosed the front panel enough with the prying tool, you can use your hands to pull the front panel off of the device.

Turn the device back over and use a plastic opening tool to detach the adhesive glue securing the front casing.

You will need to wedge a plastic opening tool in between the front casing and the screen. Then move the tool around the perimeter of the device to break the adhesive.

Once you’ve loosed the front panel enough with the prying tool, you can use your hands to pull the front panel off of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 1 other contributor

                    Dave Dorzback

Member since: 09/28/2016

602 Reputation

                                      4 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team 1-4, Cagle Fall 2016                        

                                                  Member of USF Tampa, Team 1-4, Cagle Fall 2016 



                    USFT-CAGLE-F16S1G4                     


                                            3 Members                     


                                            14 Guides authored

Oscar C - Nov 19, 2018

To install the new screen, install the connector at the top first and dry fit before installing and make sure you align the Button and Camera.

Introduction#

What you need#

Team#

Introduction

What you need

Team