Difficulty
Moderate
Steps
14
Time Required
35 minutes
Sections
1
- Camera Replacement
- 14 steps
Flags
Missed a Step
Oops! This guide is currently missing some important steps.
BackSamsung Galaxy Tablet E 9.6 Wi-Fi
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Camera Replacement
- Place the Tablet on a flat surface
- Gather the required tools: iFixit opening tool, iFixit opening picks, precision tweezers, suction handle, and spudger.
Place the Tablet on a flat surface
Gather the required tools: iFixit opening tool, iFixit opening picks, precision tweezers, suction handle, and spudger.
1024
Step 2
- Place suction handle in the center of the screen. Firmly press it downwards.
- This is done to help assist lifting the screen once the edges are loose.
Place suction handle in the center of the screen. Firmly press it downwards.
This is done to help assist lifting the screen once the edges are loose.
Step 3
- Grab the iFixit opening tool and wedge the sharp end into the corner of the screen. Pry it upwards, lifting up the corner of the screen.
Grab the iFixit opening tool and wedge the sharp end into the corner of the screen. Pry it upwards, lifting up the corner of the screen.
Step 4
- Place the iFixit opening pick between the lifted corner and the housing to prevent the screen from falling back into the housing.
Place the iFixit opening pick between the lifted corner and the housing to prevent the screen from falling back into the housing.
Step 5
- Continue around the perimeter of the screen until you have placed the picks in each remaining corner.
- Be careful removing the double-sided tape while lifting the screen so that the screen does not break.
Continue around the perimeter of the screen until you have placed the picks in each remaining corner.
Be careful removing the double-sided tape while lifting the screen so that the screen does not break.
Step 6
- Grab the suction handle and gently lift the screen towards the top of the tablet.
- Take care while lifting the screen to avoid damaging the ribbon cable at the top of the tablet.
Grab the suction handle and gently lift the screen towards the top of the tablet.
Take care while lifting the screen to avoid damaging the ribbon cable at the top of the tablet.
Step 7
- Place the removed screen that is still attached to the ribbon cable flat on the table.
Place the removed screen that is still attached to the ribbon cable flat on the table.
Step 8
- Grab the iFixit opening tool and wedge the sharp end into the corner of the housing and pry upwards.
- Place an iFixit opening pick between the housing and the LCD assembly.
Grab the iFixit opening tool and wedge the sharp end into the corner of the housing and pry upwards.
Place an iFixit opening pick between the housing and the LCD assembly.
Step 9
- Continue along the outer edge of the housing until you have placed an iFixit opening pick in each corner.
Continue along the outer edge of the housing until you have placed an iFixit opening pick in each corner.
Step 10
- Remove the LCD assembly from the housing and place it face down on the table.
Remove the LCD assembly from the housing and place it face down on the table.
Step 11
- Locate the ribbon cable connector on the back of the LCD assembly.
- Use the spudger to pry the ZIF connector lock tab upwards.
- Pull the the ribbon cable to remove it from the connector.
Locate the ribbon cable connector on the back of the LCD assembly.
Use the spudger to pry the ZIF connector lock tab upwards.
Pull the the ribbon cable to remove it from the connector.
Step 12
- Use the curved precision tweezers and carefully peel off the protective green film on top of the camera connector.
Use the curved precision tweezers and carefully peel off the protective green film on top of the camera connector.
Step 13
- Use the spudger and gently pry the ZIF connector lock tab upwards, releasing the ribbon cable.
Use the spudger and gently pry the ZIF connector lock tab upwards, releasing the ribbon cable.
Step 14
- Grab the camera and pull up and away from the connector.
Grab the camera and pull up and away from the connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Matthew Skoog
Member since: 05/22/2019
247 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
IUPUI, Team S4-G4, Wilson Summer 2019
Member of IUPUI, Team S4-G4, Wilson Summer 2019
IUPUI-WILSON-SU19S4G4
4 Members
4 Guides authored
