Samsung Galaxy Tab S2 9 7 At T Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Screen
5 steps
Screws
2 steps
Battery
4 steps

Flags

BackSamsung Galaxy Tab S2 9.7 (2015) AT&T
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Apply the heat gun around the edges of the tablet to melt the adhesive glue.
Do not allow the gun to remain still for more than two seconds, so that you do not melt the plastic around the screen.
If you do not have access to a heat gun, you may also use an iOpener or a hair dryer. Refer to the iOpener guide for extra help.

Apply the heat gun around the edges of the tablet to melt the adhesive glue.

Do not allow the gun to remain still for more than two seconds, so that you do not melt the plastic around the screen.

If you do not have access to a heat gun, you may also use an iOpener or a hair dryer. Refer to the iOpener guide for extra help.

1024

Step 2

Apply the suction to the bottom or top right corner.
Use the plastic opening tool at several points around the screen while the suction is being applied to pop the screen out.

Apply the suction to the bottom or top right corner.

Use the plastic opening tool at several points around the screen while the suction is being applied to pop the screen out.

Step 3

Once the screen is detached, open the tablet like a book.
Gently open the tablet, and do not pull the pieces apart since you can risk damaging the orange ribbon cable.

Once the screen is detached, open the tablet like a book.

Gently open the tablet, and do not pull the pieces apart since you can risk damaging the orange ribbon cable.

Step 4

Using the precision tweezers, remove the silver tape that is holding the orange ribbon cable connecting the two pieces.

Using the precision tweezers, remove the silver tape that is holding the orange ribbon cable connecting the two pieces.

Step 5

Using the precision tweezers, remove the small press-fit connector from the body of the tablet.

Using the precision tweezers, remove the small press-fit connector from the body of the tablet.

Step 6

              Screws

Using the Philips #000 screwdriver, remove the seventeen 2.74 mm screws around the edges.
Remove the two 2.74 mm black screws in the middle of the tablet with the Philips #000 screwdriver.
Put the screws on a magnetic project mat or in a container so that you do not lose them.

Using the Philips #000 screwdriver, remove the seventeen 2.74 mm screws around the edges.

Remove the two 2.74 mm black screws in the middle of the tablet with the Philips #000 screwdriver.

Put the screws on a magnetic project mat or in a container so that you do not lose them.

Step 7

Take the plastic opening tool around the tablet to remove the motherboard from the device.

Take the plastic opening tool around the tablet to remove the motherboard from the device.

Step 8

              Battery

At the bottom left of the battery, use the plastic opening tool to detach the lower press-fit connector of the black ribbon cable.
Using the plastic opening tool, detach the press-fit connector on the left side of the black ribbon cable.
Lift up the black ribbon cable to remove it.

At the bottom left of the battery, use the plastic opening tool to detach the lower press-fit connector of the black ribbon cable.

Using the plastic opening tool, detach the press-fit connector on the left side of the black ribbon cable.

Lift up the black ribbon cable to remove it.

Step 9

Using the plastic opening tool, detach the orange ribbon cable connecting the battery to the motherboard.

Using the plastic opening tool, detach the orange ribbon cable connecting the battery to the motherboard.

Step 10

Using the Phillips #000 Screwdriver, remove the four 2.74mm black screws around the edge of the battery.

Using the Phillips #000 Screwdriver, remove the four 2.74mm black screws around the edge of the battery.

Step 11

The battery is now fully detached from the motherboard.
Lift up the battery to remove it from the motherboard.

The battery is now fully detached from the motherboard.

Lift up the battery to remove it from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors

                    Joy Harris

Member since: 02/15/2017

814 Reputation

                                      7 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team S3-G4, Sullivan Spring 2017                        

                                                  Member of USF Tampa, Team S3-G4, Sullivan Spring 2017 



                    USFT-SULLIVAN-S17S3G4                     


                                            3 Members                     


                                            14 Guides authored

vatin1998 - Oct 22, 2019

impossible de décoller l’écran de la tablette

Christian Muller - May 19, 2020

Le tuto est parfaitement clair et précis. Un grand Merci.

Néanmoins il faut reconnaître que cette opération n’est pas simple du tout et qu’elle n’est pas sans risque, même en étant très méticuleux.

Pour ouvrir la coque, il faut obligatoirement un minimum de matériel adapté et malgré cela, c’est une galère !

Sébastien Colonges - Feb 24, 2021

Pour info sur la Galaxy tab s2 votre tuto est faux. Merci j’ai cassé le haut de mon écran. Grace à un autre site jai pu voir qu’il faut enlever le capot arrière pour accéder à la batterie

Introduction#

What you need#

Team#

Introduction

What you need

Team