Difficulty
Moderate
Steps
7
Time Required
20 minutes - 1 hour
Sections
1
- Screen
- 7 steps
Flags
0
BackSamsung Galaxy Tab S2 9.7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Heat the iOpeners in a microwave for 1-2 minutes.
- The iOpeners will be hot. Use caution and hold the tabs on the ends.
- Place heated iOpeners on screen edges to heat the adhesive.
- For more detailed instructions on how to use the iOpeners, please refer to the iOpener Instructions.
Heat the iOpeners in a microwave for 1-2 minutes.
The iOpeners will be hot. Use caution and hold the tabs on the ends.
Place heated iOpeners on screen edges to heat the adhesive.
For more detailed instructions on how to use the iOpeners, please refer to the iOpener Instructions.
1024
Step 2
- Separate the screen assembly from the back by wedging the picks between the two components.
- Slide the picks along the edge and leave them holding the device open all around the edges.
Separate the screen assembly from the back by wedging the picks between the two components.
Slide the picks along the edge and leave them holding the device open all around the edges.
Step 3
- Place suctioning device near the corner of the screen and gently lift up to create a gap between the front panel assembly and the back.
- Insert the picks to hold the two components apart once a gap is created.
Place suctioning device near the corner of the screen and gently lift up to create a gap between the front panel assembly and the back.
Insert the picks to hold the two components apart once a gap is created.
Step 4
- Once all edges have been disconnected, carefully lift the screen off by pulling one side up.
- Be careful not to cut yourself. Any broken glass from the screen will be sharp.
Once all edges have been disconnected, carefully lift the screen off by pulling one side up.
Be careful not to cut yourself. Any broken glass from the screen will be sharp.
Step 5
- Using the tweezers, gently peel up on the silver tape covering the connector.
Using the tweezers, gently peel up on the silver tape covering the connector.
Step 6
- Use the plastic opening tool to get under the connector piece. This will allow you to remove the front panel assembly from the rest of the device.
Use the plastic opening tool to get under the connector piece. This will allow you to remove the front panel assembly from the rest of the device.
Step 7
- Detach the connecter from the inside of the device.
- Lift the screen to separate the front panel assembly from the rest of the device.
Detach the connecter from the inside of the device.
Lift the screen to separate the front panel assembly from the rest of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 4 other contributors
Kaley Sapper
Member since: 04/18/2018
697 Reputation
2 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S16-G5, Livingston Spring 2018
Member of Cal Poly, Team S16-G5, Livingston Spring 2018
CPSU-LIVINGSTON-S18S16G5
5 Members
12 Guides authored
Dick Campbell - Jul 1, 2019
Reply
Question. How is the new LCD re-attached? Do you reheat the old adhesive so that it sticks to the new LCD? Or do you need to apply new adhesive? Or is there a double-sided tape to re-attach the new LCD?
Stefano Vaccarone - Nov 16, 2020
Reply
Hi,
my glass broke, not the LCD itself. Do you know how to separate LCD and glass, change the glass, and put it back again?
I have found a video on the internet but a laminating machine seems needed?? Any easier solution?
Thanks
Chris - Nov 18, 2020
I would like to know also
