Samsung Gear 360 Rear Camera Replacement Repair Guide

Difficulty

Difficult

Steps

18

Time Required

                          30 minutes - 1 hour            

Sections

2

• Case
• 13 steps
• Rear Camera
• 5 steps

Flags

1

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

• BackSamsung Gear 360

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Case               

• Twist silver ring on the lens counter-clockwise with force to remove it.

Twist silver ring on the lens counter-clockwise with force to remove it.

1024

Step 2

• Insert a small flathead screwdriver into marked slot on camera lens and pry off camera lens cover.

Insert a small flathead screwdriver into marked slot on camera lens and pry off camera lens cover.

Step 3

• Using a PH00 screwdriver head, remove all Phillips #00 0.75 mm screws on the front of the camera.
• Repeat for the back side of the camera.

Using a PH00 screwdriver head, remove all Phillips #00 0.75 mm screws on the front of the camera.

Repeat for the back side of the camera.

Step 4

• Peel off the black rubber located on the bottom of the device using your hand or a small flathead screwdriver.

Peel off the black rubber located on the bottom of the device using your hand or a small flathead screwdriver.

Step 5

• Once the black rubber has been removed, unscrew all Phillips #00 0.75 mm screws on the bottom of the device using a PH00 screwdriver head.

Once the black rubber has been removed, unscrew all Phillips #00 0.75 mm screws on the bottom of the device using a PH00 screwdriver head.

Step 6

• Using a plastic opening tool, pry the tripod mount off the device.

Using a plastic opening tool, pry the tripod mount off the device.

Step 7

• Using both hands, carefully remove the right cover off the camera body.

Using both hands, carefully remove the right cover off the camera body.

Step 8

• To remove the left cover of the camera body, lift the left cover using a small flathead screwdriver and pull it off.

To remove the left cover of the camera body, lift the left cover using a small flathead screwdriver and pull it off.

Step 9

• Once the camera body has been removed, lift and pull off the metal support ring using a small flathead screwdriver.
• Repeat for both sides of the camera.

Once the camera body has been removed, lift and pull off the metal support ring using a small flathead screwdriver.

Repeat for both sides of the camera.

Step 10

• Remove all Phillips #00 0.75 mm screws from the body of the camera using a PH00 screwdriver head.

Remove all Phillips #00 0.75 mm screws from the body of the camera using a PH00 screwdriver head.

Step 11

• Carefully lift the three sensors off using a plastic opening tool and pull them aside.

Carefully lift the three sensors off using a plastic opening tool and pull them aside.

Step 12

• Carefully use a plastic opening tool to separate the gray case from the black case on the device.

Carefully use a plastic opening tool to separate the gray case from the black case on the device.

Step 13

• Insert a plastic removal tool underneath the four sensors on the motherboard to fully separate the camera case.

Insert a plastic removal tool underneath the four sensors on the motherboard to fully separate the camera case.

Step 14

              Rear Camera               

• Within the grey half of the case, unscrew both Phillips #00 0.75 mm screws located on the metal plate using PH00 screwdriver.

Within the grey half of the case, unscrew both Phillips #00 0.75 mm screws located on the metal plate using PH00 screwdriver.

Step 15

• Once the screws have been removed, remove the metal plate.

Once the screws have been removed, remove the metal plate.

Step 16

• Using a PH000 screwdriver head, remove the both Phillips #000 0.75 mm screws on the grey case.

Using a PH000 screwdriver head, remove the both Phillips #000 0.75 mm screws on the grey case.

Step 17

• Using a plastic opening tool, remove the plastic cover underneath the rear camera

Using a plastic opening tool, remove the plastic cover underneath the rear camera

Step 18

• Gently remove the rear camera module by using a plastic opening tool and lifting the module.

Gently remove the rear camera module by using a plastic opening tool and lifting the module.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Connor                     

Member since: 02/20/2017

436 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       USF Tampa, Team S3-G5, Sullivan Spring 2017                        

                                                  Member of USF Tampa, Team S3-G5, Sullivan Spring 2017 



                    USFT-SULLIVAN-S17S3G5                     


                                            4 Members                     


                                            14 Guides authored                     

Pelicula 360 - Aug 3, 2017

Reply

number datasheet sensor camera?