Samsung Gravity Txt Plastic Back Frame Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Battery
3 steps
SIM Card
1 step
microSD Card
1 step
Plastic Back Frame
2 steps

Flags

BackSamsung Gravity TXT
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Pry the back cover off with a plastic opening tool, or your fingernail, in the indentation on the bottom of the device.

Pry the back cover off with a plastic opening tool, or your fingernail, in the indentation on the bottom of the device.

1024

Step 2

Lift the back cover away from the main body of the phone.

Lift the back cover away from the main body of the phone.

Step 3

Insert your finger in the groove below the battery.
Press the battery toward the audio jack while lifting upward and away from the phone.
Remember to place the battery back with the copper contacts on the battery lined up with those on the phone.

Insert your finger in the groove below the battery.

Press the battery toward the audio jack while lifting upward and away from the phone.

Remember to place the battery back with the copper contacts on the battery lined up with those on the phone.

Step 4

              SIM Card

Using your finger, push the SIM Card down and slide out of the slot.
Slide the SIM card out enough to grab it firmly.
Remove the SIM card away from the phone.
Follow the visual on the bottom of the SIM card slot to put the SIM card back in the correct orientation.
When sliding the SIM Card back in the slot, make sure the card goes all the way in the slot until it hits the stopper.

Using your finger, push the SIM Card down and slide out of the slot.

Slide the SIM card out enough to grab it firmly.

Remove the SIM card away from the phone.

Follow the visual on the bottom of the SIM card slot to put the SIM card back in the correct orientation.

When sliding the SIM Card back in the slot, make sure the card goes all the way in the slot until it hits the stopper.

Step 5

              microSD Card

Using your fingernail, push the microSD card slightly deeper into the slot, until you hear a click.
The removal of the battery is not required for this operation; therefore, step 3 can be skipped if just replacing the microSD card.
After the click, release the microSD card to allow it to pop out.
Remove the microSD card from its slot
When placing the microSD card back in the phone, make sure the card clicks in place.

Using your fingernail, push the microSD card slightly deeper into the slot, until you hear a click.

The removal of the battery is not required for this operation; therefore, step 3 can be skipped if just replacing the microSD card.

After the click, release the microSD card to allow it to pop out.

Remove the microSD card from its slot

When placing the microSD card back in the phone, make sure the card clicks in place.

Step 6

              Plastic Back Frame

Remove the six 3 mm #00 Phillips screws in the plastic back frame.

Remove the six 3 mm #00 Phillips screws in the plastic back frame.

Step 7

Slide the keyboard out.
Use a Jimmy to separate a small segment of the plastic back frame from rest of the phone.
Starting at the bottom of the keyboard is recommended.
Slide an opening pick around the rest of the seam, starting at the gap just created with the Jimmy.
You will have to slide the keyboard back in to separate the back frame from the top have of the keyboard slider.
Lift the plastic back frame away.

Slide the keyboard out.

Use a Jimmy to separate a small segment of the plastic back frame from rest of the phone.

Starting at the bottom of the keyboard is recommended.

Slide an opening pick around the rest of the seam, starting at the gap just created with the Jimmy.

You will have to slide the keyboard back in to separate the back frame from the top have of the keyboard slider.

Lift the plastic back frame away.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Josh Brown

Member since: 07/07/2015

222 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       IUPUI, Team 1-1, Renguette SU 2015                        

                                                  Member of IUPUI, Team 1-1, Renguette SU 2015 



                    IUPUI-RENGUETTE-SU15S1G1                     


                                            5 Members                     


                                            16 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team