Difficulty

Very difficult

Steps

10

Time Required

                          10 - 15 minutes

Sections

3

  • Battery
  • 1 step
  • Strap Side Outer Casing
  • 4 steps
  • Lens
  • 5 steps

Flags

0

  • BackSamsung HMX-F90

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Pull the release tab away from the battery.
  • Slide the battery towards the release tab and then pull the battery away from the camcorder.

Pull the release tab away from the battery.

Slide the battery towards the release tab and then pull the battery away from the camcorder.

1024

Step 2

              Strap Side Outer Casing
  • Rotate the camcorder so that the strap side is facing you.
  • Locate and remove the three 4.5mm Phillips #00 screws around the hand strap.

Rotate the camcorder so that the strap side is facing you.

Locate and remove the three 4.5mm Phillips #00 screws around the hand strap.

Step 3

  • Rotate the camcorder so that the battery slot is facing you.
  • Located in the top left corner of the battery slot, remove the 4.5mm Phillips #00 screw.

Rotate the camcorder so that the battery slot is facing you.

Located in the top left corner of the battery slot, remove the 4.5mm Phillips #00 screw.

Step 4

  • Rotate the camcorder so you are looking at the bottom of the camcorder.
  • Locate and remove the last three 4.5mm Phillips #00 screws.

Rotate the camcorder so you are looking at the bottom of the camcorder.

Locate and remove the last three 4.5mm Phillips #00 screws.

Step 5

  • With both hands, pull the side strap apart from the rest of the camcorder.

With both hands, pull the side strap apart from the rest of the camcorder.

Step 6

              Lens
  • Rotate the camcorder so that back is facing you. Then flip open the LCD screen.
  • Locate and remove the 4.5mm Phillips #00 screws in the LCD screen base.

Rotate the camcorder so that back is facing you. Then flip open the LCD screen.

Locate and remove the 4.5mm Phillips #00 screws in the LCD screen base.

Step 7

  • Close the LCD screen. Then lift the silver base away from the camcorder.

Close the LCD screen. Then lift the silver base away from the camcorder.

Step 8

  • Locate and remove the two 3.5mm Phillips #00 screws from the side of the camcorder.

Locate and remove the two 3.5mm Phillips #00 screws from the side of the camcorder.

Step 9

  • Gradually pry off the outer casing using a prying tool.

Gradually pry off the outer casing using a prying tool.

Step 10

  • Locate and remove the three 4mm Phillips #00 screws around the lens.
  • Gently remove the lens.

Locate and remove the three 4mm Phillips #00 screws around the lens.

Gently remove the lens.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor 


                    Amir Harb

Member since: 09/26/2017

697 Reputation

                                      6 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team S13-G1, Boczar Fall 2017                        

                                                  Member of USF Tampa, Team S13-G1, Boczar Fall 2017 



                    USFT-BOCZAR-F17S13G1                     


                                            4 Members                     


                                            12 Guides authored