Difficulty

Moderate

Steps

11

Time Required

                          15 minutes

Sections

2

  • Removing Back Cover
  • 5 steps
  • LCD Screen
  • 6 steps

Flags

1

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

  • BackSamsung L100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Removing Back Cover
  • Remove the six external screws from the camera using a Phillips #0 screwdriver.
  • After the screws has been removed, the bottom of the back half of the external case should be loosened from the camera.
  • Be careful, make sure you don’t lose the screws.

Remove the six external screws from the camera using a Phillips #0 screwdriver.

After the screws has been removed, the bottom of the back half of the external case should be loosened from the camera.

Be careful, make sure you don’t lose the screws.

1024

Step 2

  • Open the battery cover that’s located on the bottom right side of the camera and carefully remove the battery.

Open the battery cover that’s located on the bottom right side of the camera and carefully remove the battery.

Step 3

  • Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera.

Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera.

Step 4

  • Carefully squeeze the top right corner of the camera and pry off the external cover.
  • If you hear a “cracking” sound. This is normal.
  • Continue to pull the external cover and it will come off cleanly.
  • Be cautious of the flash capacitor. It carries an electrical charge, that may give you an unpleasant shock.

Carefully squeeze the top right corner of the camera and pry off the external cover.

If you hear a “cracking” sound. This is normal.

Continue to pull the external cover and it will come off cleanly.

Be cautious of the flash capacitor. It carries an electrical charge, that may give you an unpleasant shock.

Step 5

  • Carefully pull off the back cover, parts behind the back of the case might fall out.

Carefully pull off the back cover, parts behind the back of the case might fall out.

Step 6

              LCD Screen
  • Remove the screws holding the circuit board.
  • Carefully remove the circuit board.

Remove the screws holding the circuit board.

Carefully remove the circuit board.

Step 7

  • Carefully lift circuit board from camera.
  • Circuit board still attached to camera by ribbon.

Carefully lift circuit board from camera.

Circuit board still attached to camera by ribbon.

Step 8

  • Remove the front cover. It should come off easily.
  • Buttons might fall out when you remove the front cover.

Remove the front cover. It should come off easily.

Buttons might fall out when you remove the front cover.

Step 9

  • Remove the green tape that holds the LCD screen.
  • Carefully lift the LCD Screen.

Remove the green tape that holds the LCD screen.

Carefully lift the LCD Screen.

Step 10

  • Flip the camera over to the other side.
  • Lift the black strip and the ribbon should easily come out.
  • The LCD Screen should be completely separated from the camera now.

Flip the camera over to the other side.

Lift the black strip and the ribbon should easily come out.

The LCD Screen should be completely separated from the camera now.

Step 11

  • Insert the new LCD Screen by pushing the ribbon into the slot.
  • Flip the black strip back down to lock the ribbon in.
  • Your new LCD Screen should be connected to the camera now.

Insert the new LCD Screen by pushing the ribbon into the slot.

Flip the black strip back down to lock the ribbon in.

Your new LCD Screen should be connected to the camera now.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Hasit

Member since: 04/15/2010

183 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 6-17, Maness Spring 2010                        

                                                  Member of Cal Poly, Team 6-17, Maness Spring 2010 



                    CPSU-MANESS-S10S6G17                     


                                            4 Members                     


                                            10 Guides authored