Difficulty
Moderate
Steps
19
Time Required
15 - 30 minutes
Sections
4
- Battery
- 3 steps
- Screen
- 6 steps
- Lens Assembly
- 6 steps
- Flash Bulb Assembly
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackSamsung MV900F
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Slide the lock towards the middle of the camera, in the same direction of the arrow.
Slide the lock towards the middle of the camera, in the same direction of the arrow.
1024
Step 2
- Push the blue battery holder up in the direction of the arrow.
Push the blue battery holder up in the direction of the arrow.
Step 3
- Pull the battery out of the battery slot.
Pull the battery out of the battery slot.
Step 4
Screen
- Use tweezers to remove the four rubber screw covers.
Use tweezers to remove the four rubber screw covers.
Step 5
- Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.
Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.
Step 6
- Remove the back casing by just carefully pulling the casing off of the camera.
Remove the back casing by just carefully pulling the casing off of the camera.
Step 7
- Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.
Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.
Step 8
- Use plastic opening tool to disconnect screen connector from the control board.
Use plastic opening tool to disconnect screen connector from the control board.
Step 9
- Remove the old screen.
Remove the old screen.
Step 10
Lens Assembly
- Remove the 2.381 mm screw with a Phillips #00 screwdriver.
Remove the 2.381 mm screw with a Phillips #00 screwdriver.
Step 11
- Use the plastic opening tool to remove the silver metal lens cover.
Use the plastic opening tool to remove the silver metal lens cover.
Step 12
- Use the tweezers to remove the black electrical tape covering the copper connector to the control board.
Use the tweezers to remove the black electrical tape covering the copper connector to the control board.
Step 13
- From the front of the camera, push the lens through the back of the camer.a
From the front of the camera, push the lens through the back of the camer.a
Step 14
- Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.
Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.
Step 15
- Remove the lens assembly from the camera.
Remove the lens assembly from the camera.
Step 16
Flash Bulb Assembly
- Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.
Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.
Step 17
- Use tweezers to pull copper connector from the control board.
Use tweezers to pull copper connector from the control board.
Step 18
- Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.
Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.
Step 19
- Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.
Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Justin Smith
Member since: 03/03/2015
95 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
Sam Houston State, Team 13-2, Blackburne Winter 2015
Member of Sam Houston State, Team 13-2, Blackburne Winter 2015
SHSU-BLACKBURNE-W15S13G2
3 Members
8 Guides authored
