Difficulty

Moderate

Steps

15

Time Required

                          10 - 15 minutes

Sections

3

  • Battery
  • 3 steps
  • Screen
  • 6 steps
  • Lens Assembly
  • 6 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackSamsung MV900F

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Battery
  • Slide the lock towards the middle of the camera, in the same direction of the arrow.

Slide the lock towards the middle of the camera, in the same direction of the arrow.

1024

Step 2

  • Push the blue battery holder up in the direction of the arrow.

Push the blue battery holder up in the direction of the arrow.

Step 3

  • Pull the battery out of the battery slot.

Pull the battery out of the battery slot.

Step 4

              Screen
  • Use tweezers to remove the four rubber screw covers.

Use tweezers to remove the four rubber screw covers.

Step 5

  • Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.

Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.

Step 6

  • Remove the back casing by just carefully pulling the casing off of the camera.

Remove the back casing by just carefully pulling the casing off of the camera.

Step 7

  • Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.

Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.

Step 8

  • Use plastic opening tool to disconnect screen connector from the control board.

Use plastic opening tool to disconnect screen connector from the control board.

Step 9

  • Remove the old screen.

Remove the old screen.

Step 10

              Lens Assembly
  • Remove the 2.381 mm screw with a Phillips #00 screwdriver.

Remove the 2.381 mm screw with a Phillips #00 screwdriver.

Step 11

  • Use the plastic opening tool to remove the silver metal lens cover.

Use the plastic opening tool to remove the silver metal lens cover.

Step 12

  • Use the tweezers to remove the black electrical tape covering the copper connector to the control board.

Use the tweezers to remove the black electrical tape covering the copper connector to the control board.

Step 13

  • From the front of the camera, push the lens through the back of the camer.a

From the front of the camera, push the lens through the back of the camer.a

Step 14

  • Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.

Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.

Step 15

  • Remove the lens assembly from the camera.

Remove the lens assembly from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Ethan Rowland

Member since: 03/03/2015

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Sam Houston State, Team 13-2, Blackburne Winter 2015                        

                                                  Member of Sam Houston State, Team 13-2, Blackburne Winter 2015 



                    SHSU-BLACKBURNE-W15S13G2                     


                                            3 Members                     


                                            8 Guides authored