Difficulty
Moderate
Steps
9
Time Required
6 minutes
Sections
3
- Back Case
- 4 steps
- Battery
- 2 steps
- Cooling Fan
- 3 steps
Flags
0
BackSamsung NP510R5E-A01UB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Case
- Lightly press down on the the back panel and pull away from the back case. The panel should slide away and detach from the back case.
Lightly press down on the the back panel and pull away from the back case. The panel should slide away and detach from the back case.
1024
Step 2
- Remove the two rubber feet that have arrows pointing towards them. The rubber feet are very sticky so use the metal spudger to pry them up.
Remove the two rubber feet that have arrows pointing towards them. The rubber feet are very sticky so use the metal spudger to pry them up.
Step 3
- Using the JIS #0 screwdriver, remove all the screws in the back case.
- Unscrew the 9 black 6.5mm screws.
- Unscrew the 4 silver 4.4mm screws.
Using the JIS #0 screwdriver, remove all the screws in the back case.
Unscrew the 9 black 6.5mm screws.
Unscrew the 4 silver 4.4mm screws.
Step 4
- Using the spudger, insert it between the back case and the laptop. Pry up on the back case until the case pops up. Work the spudger all the way around the back case until the back case will lift off freely.
Using the spudger, insert it between the back case and the laptop. Pry up on the back case until the case pops up. Work the spudger all the way around the back case until the back case will lift off freely.
Step 5
Battery
- Remove the two rubber feet with arrows by them on the back side to uncover two screws.
- Unscrew the four silver 4.4mm long screws near the hard drive.
- Unscrew the remaining nine black 6.5mm long screws. Then remove the back casing using a pry tool if needed.
Remove the two rubber feet with arrows by them on the back side to uncover two screws.
Unscrew the four silver 4.4mm long screws near the hard drive.
Unscrew the remaining nine black 6.5mm long screws. Then remove the back casing using a pry tool if needed.
Step 6
- Use the screwdriver to remove the four 3.5mm long screws holding the battery in place. Then carefully pull the battery’s connector cable out to remove the battery.
Use the screwdriver to remove the four 3.5mm long screws holding the battery in place. Then carefully pull the battery’s connector cable out to remove the battery.
Step 7
Cooling Fan
- Unplug the fan cord.
Unplug the fan cord.
Step 8
- Use the Phillips #0 screwdriver to remove the two 3.0mm screws.
- Loosen the four spring loaded screws using the Phillips #0 screwdriver. These do NOT come out.
Use the Phillips #0 screwdriver to remove the two 3.0mm screws.
Loosen the four spring loaded screws using the Phillips #0 screwdriver. These do NOT come out.
Step 9
- Use the Phillips #0 screwdriver to remove the five 3.0mm screws.
- Remove the fan from the copper plate.
Use the Phillips #0 screwdriver to remove the five 3.0mm screws.
Remove the fan from the copper plate.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Jared Thomas
Member since: 03/25/2019
121 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
IUPUI, Team S2-G2, Henning Spring 2019
Member of IUPUI, Team S2-G2, Henning Spring 2019
IUPUI-HENNING-S19S2G2
3 Members
3 Guides authored
