Difficulty

Moderate

Steps

11

Time Required

                          5 - 10 minutes

Sections

2

  • Hard Drive
  • 3 steps
  • Speaker
  • 8 steps

Flags

0

  • BackSamsung NP510R5E-A01UB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Hard Drive
  • Make sure the device is powered off before beginning.
  • Using the Phillips #0 screwdriver, remove the 6.5mm long screw in the area circled.

Make sure the device is powered off before beginning.

Using the Phillips #0 screwdriver, remove the 6.5mm long screw in the area circled.

1024

Step 2

  • With the cover removed, unscrew all four of the 4.75mm long screws using the Phillips #0 screwdriver.

With the cover removed, unscrew all four of the 4.75mm long screws using the Phillips #0 screwdriver.

Step 3

  • Unplug the connector from the hard drive by pulling straight out.

Unplug the connector from the hard drive by pulling straight out.

Step 4

              Speaker
  • Remove the two rubber feet with arrows by them on the back side to uncover two screws.
  • Unscrew the four silver 4.4mm long screws near the hard drive.
  • Unscrew the remaining nine black 6.5mm long screws. Then remove the back casing using a pry tool if needed.

Remove the two rubber feet with arrows by them on the back side to uncover two screws.

Unscrew the four silver 4.4mm long screws near the hard drive.

Unscrew the remaining nine black 6.5mm long screws. Then remove the back casing using a pry tool if needed.

Step 5

  • Untangle the wires attached to the exterior of the right speaker.
  • Lift the tape up holding the wires down to fully release the wires.

Untangle the wires attached to the exterior of the right speaker.

Lift the tape up holding the wires down to fully release the wires.

Step 6

  • Unscrew the 3.4mm long screw holding the right speaker in place.

Unscrew the 3.4mm long screw holding the right speaker in place.

Step 7

  • Pull up on the wires circled to disconnect the right speaker.

Pull up on the wires circled to disconnect the right speaker.

Step 8

  • Using the plastic opening tool, pry up the right speaker and take it out.

Using the plastic opening tool, pry up the right speaker and take it out.

Step 9

  • Unscrew the 3.4mm long screw holding the left speaker in place.

Unscrew the 3.4mm long screw holding the left speaker in place.

Step 10

  • Pull up on the wires to disconnect the left speaker.

Pull up on the wires to disconnect the left speaker.

Step 11

  • Using the plastic opening tool, pry up the left speaker and take it out.

Using the plastic opening tool, pry up the left speaker and take it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Brian Briggs

Member since: 02/14/2018

508 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team S6-G5, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S6-G5, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S6G5                     


                                            3 Members                     


                                            8 Guides authored