Samsung Nx1000 Back Panel Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          10 - 20 minutes            

Sections

3

• Back Panel
• 6 steps
• Back Panel Components
• 3 steps
• Back Panel
• 2 steps

Flags

0

• BackSamsung NX1000

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Removing the Back Panel               

• Locate the bottom panel of the camera.
• Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.
• Push the screwdriver firmly into the screw so that the driver will not strip the screw.

Locate the bottom panel of the camera.

Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.

Push the screwdriver firmly into the screw so that the driver will not strip the screw.

1024

Step 2

• Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.

Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.

Step 3

• Pry open the back panel using the metal spudger.
• Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.

Pry open the back panel using the metal spudger.

Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.

Step 4

• Open the two halves of the camera, taking care not to disturb the ribbon cable.
• Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step

Open the two halves of the camera, taking care not to disturb the ribbon cable.

Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step

Step 5

• Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.
• Push the ribbon out of its socket with the plastic opening tool.

Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.

Push the ribbon out of its socket with the plastic opening tool.

Step 6

• Completely separate the back panel from the camera.

Completely separate the back panel from the camera.

Step 7

              Back Panel Components               

• Remove all five 3mm Philips #000 screws from the inside of the back panel using the Philips #000 Screwdriver.

Remove all five 3mm Philips #000 screws from the inside of the back panel using the Philips #000 Screwdriver.

Step 8

• Lift up the grey tab on the ZIF connector with the spudger to remove the ribbon.
• Using both thumbs push the ribbon out of the ZIF connection.

Lift up the grey tab on the ZIF connector with the spudger to remove the ribbon.

Using both thumbs push the ribbon out of the ZIF connection.

Step 9

• Use the metal spudger to pick the bottom of the plastic piece while simultaneously using your index finger to push down on the larger metal slab. This will cause the metal plate with the large ribbon to slide down and out of the plastic back panel.
• Do not disconnect the blue ribbon.

Use the metal spudger to pick the bottom of the plastic piece while simultaneously using your index finger to push down on the larger metal slab. This will cause the metal plate with the large ribbon to slide down and out of the plastic back panel.

Do not disconnect the blue ribbon.

Step 10

              Back Panel               

• Use a metal tool to pick on the sides of the metal plate to remove the plate from the plastic tabs.

Use a metal tool to pick on the sides of the metal plate to remove the plate from the plastic tabs.

Step 11

• Separate the back panel from the LCD.

Separate the back panel from the LCD.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 6 other contributors 

                    Greg Baghdikian                     

Member since: 01/22/2015

143 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Cal Poly, Team 20-13, Maness Winter 2015                        

                                                  Member of Cal Poly, Team 20-13, Maness Winter 2015 



                    CPSU-MANESS-W15S20G13                     


                                            4 Members                     


                                            14 Guides authored