Difficulty
Easy
Steps
10
Time Required
20 - 40 minutes
Sections
3
- Back Panel
- 6 steps
- Back Panel Components
- 3 steps
- Menu Button
- 1 step
Flags
1
Missed a Step
Oops! This guide is currently missing some important steps.
BackSamsung NX1000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing the Back Panel
- Locate the bottom panel of the camera.
- Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.
- Push the screwdriver firmly into the screw so that the driver will not strip the screw.
Locate the bottom panel of the camera.
Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.
Push the screwdriver firmly into the screw so that the driver will not strip the screw.
1024
Step 2
- Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.
Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.
Step 3
- Pry open the back panel using the metal spudger.
- Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.
Pry open the back panel using the metal spudger.
Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.
Step 4
- Open the two halves of the camera, taking care not to disturb the ribbon cable.
- Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step
Open the two halves of the camera, taking care not to disturb the ribbon cable.
Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step
Step 5
- Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.
- Push the ribbon out of its socket with the plastic opening tool.
Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.
Push the ribbon out of its socket with the plastic opening tool.
Step 6
- Completely separate the back panel from the camera.
Completely separate the back panel from the camera.
Step 7
Back Panel Components
- Remove all five 3mm Philips #000 screws from the inside of the back panel using the Philips #000 Screwdriver.
Remove all five 3mm Philips #000 screws from the inside of the back panel using the Philips #000 Screwdriver.
Step 8
- Lift up the grey tab on the ZIF connector with the spudger to remove the ribbon.
- Using both thumbs push the ribbon out of the ZIF connection.
Lift up the grey tab on the ZIF connector with the spudger to remove the ribbon.
Using both thumbs push the ribbon out of the ZIF connection.
Step 9
- Use the metal spudger to pick the bottom of the plastic piece while simultaneously using your index finger to push down on the larger metal slab. This will cause the metal plate with the large ribbon to slide down and out of the plastic back panel.
- Do not disconnect the blue ribbon.
Use the metal spudger to pick the bottom of the plastic piece while simultaneously using your index finger to push down on the larger metal slab. This will cause the metal plate with the large ribbon to slide down and out of the plastic back panel.
Do not disconnect the blue ribbon.
Step 10
Menu Button
- Remove the button assembly from the back panel
Remove the button assembly from the back panel
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Yesenia
Member since: 01/22/2015
717 Reputation
6 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 20-13, Maness Winter 2015
Member of Cal Poly, Team 20-13, Maness Winter 2015
CPSU-MANESS-W15S20G13
4 Members
14 Guides authored
