Samsung Nx1000 Motherboard Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 - 40 minutes

Sections

Back Panel
6 steps
Motherboard
11 steps

Flags

BackSamsung NX1000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Removing the Back Panel

Locate the bottom panel of the camera.
Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.
Push the screwdriver firmly into the screw so that the driver will not strip the screw.

Locate the bottom panel of the camera.

Unscrew the four 4.5mm Philips #000 (perpendicular cross) screws with the Philips #000 screwdriver.

Push the screwdriver firmly into the screw so that the driver will not strip the screw.

1024

Step 2

Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.

Unscrew the three 4.5mm #000 Philips screws on the sides of the camera using the Philips #000 screwdriver.

Step 3

Pry open the back panel using the metal spudger.
Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.

Pry open the back panel using the metal spudger.

Do not completely separate the back panel from the camera. There is a ribbon on bottom left back corner underneath the buttons. The ribbon will hold the back panel to the camera. Do not jam the tool in this part or the ribbon will rip.

Step 4

Open the two halves of the camera, taking care not to disturb the ribbon cable.
Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step

Open the two halves of the camera, taking care not to disturb the ribbon cable.

Do not completely separate the halves. The ribbon cable needs to be disconnected from the ZIF connection carefully as shown in the next step

Step 5

Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.
Push the ribbon out of its socket with the plastic opening tool.

Remove the ribbon by lifting the grey tab on the ZIF connector with the metal spudger.

Push the ribbon out of its socket with the plastic opening tool.

Step 6

Completely separate the back panel from the camera.

Completely separate the back panel from the camera.

Step 7

              Motherboard

Remove the black rubber tape with the plastic opening tool and slowly peel it off.

Remove the black rubber tape with the plastic opening tool and slowly peel it off.

Step 8

Disconnect the bottom ribbon by grasping the ribbon and wiggling it out gently from the connection.

Disconnect the bottom ribbon by grasping the ribbon and wiggling it out gently from the connection.

Step 9

Open the ZIF connector on both of the larger ribbons by lifting the black latch with the plastic opening tool.

Open the ZIF connector on both of the larger ribbons by lifting the black latch with the plastic opening tool.

Step 10

Disconnect the bottom of the larger ribbons by gently wiggling it away from the ZIF connector.

Disconnect the bottom of the larger ribbons by gently wiggling it away from the ZIF connector.

Step 11

Disconnect the top of the larger ribbons by wiggling it out of the ZIF connector / prying the ribbon out with the plastic opening tool.
Make sure to remove this ribbon carefully. The ribbon is connected at the top right corner and can tear if not removed carefully.

Disconnect the top of the larger ribbons by wiggling it out of the ZIF connector / prying the ribbon out with the plastic opening tool.

Make sure to remove this ribbon carefully. The ribbon is connected at the top right corner and can tear if not removed carefully.

Step 12

Hold back the ribbons to access the second smaller one at the bottom of the camera.
Slowly wiggle the ribbon out of the ZIF connection.

Hold back the ribbons to access the second smaller one at the bottom of the camera.

Slowly wiggle the ribbon out of the ZIF connection.

Step 13

Unscrew the three 4.5mm Philips #000 screws with the Philips #000 screwdriver.

Unscrew the three 4.5mm Philips #000 screws with the Philips #000 screwdriver.

Step 14

Using the plastic opening tool lift the motherboard up starting from the bottom left side.

Using the plastic opening tool lift the motherboard up starting from the bottom left side.

Step 15

Pull out the board to the left, freeing the external ports from the plastic case.
Be careful when lifting the motherboard. There is one more ribbon cable to free before fully removing the board.

Pull out the board to the left, freeing the external ports from the plastic case.

Be careful when lifting the motherboard. There is one more ribbon cable to free before fully removing the board.

Step 16

Carefully place the motherboard back down to remove the last ribbon. Lift the black latch up from the ZIF connector of the last ribbon with the plastic opening tool.

Carefully place the motherboard back down to remove the last ribbon. Lift the black latch up from the ZIF connector of the last ribbon with the plastic opening tool.

Step 17

Slowly and carefully wiggle the ribbon out of the ZIF connection (Do this by holding the back of the ribbon).

Slowly and carefully wiggle the ribbon out of the ZIF connection (Do this by holding the back of the ribbon).

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Yesenia

Member since: 01/22/2015

717 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 20-13, Maness Winter 2015                        

                                                  Member of Cal Poly, Team 20-13, Maness Winter 2015 



                    CPSU-MANESS-W15S20G13                     


                                            4 Members                     


                                            14 Guides authored

alhilal509 - Aug 8, 2020

Is NX210 works the same way?

Introduction#

What you need#

Team#

Introduction

What you need

Team