Samsung Nx3000 Lcd Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
Lens Assembly
3 steps
Back Case
7 steps
LCD
5 steps

Flags

BackSamsung NX3000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

We highly suggest you use a magnetic project mat or an organization tray. This camera has many different types of screws and keeping them organized is key to proper reassembly.

What you need

Step 1

              Battery

If you haven’t done so already, remove the lens from the camera.
Turn the camera upside down.
Slide the button to the left to open the battery compartment.
Push the blue button up to release the battery.
The battery is not shown in these photos.

If you haven’t done so already, remove the lens from the camera.

Turn the camera upside down.

Slide the button to the left to open the battery compartment.

Push the blue button up to release the battery.

The battery is not shown in these photos.

1024

Step 2

              Lens Assembly

Remove the four 7.3 mm Phillips screws from the front of the lens assembly.
Remove the silver ring with tweezers.

Remove the four 7.3 mm Phillips screws from the front of the lens assembly.

Remove the silver ring with tweezers.

Step 3

Use tweezers to remove the black plastic ring and small metal ring inside the lens assembly.

Use tweezers to remove the black plastic ring and small metal ring inside the lens assembly.

Step 4

Use tweezers to lift the pyramid screw and spring from the lens assembly.

Use tweezers to lift the pyramid screw and spring from the lens assembly.

Step 5

              Back Case

Remove the three 4.3 mm Phillips screws from the bottom of the camera.
Remove the 4.3 mm Phillips screw hiding inside the battery compartment.

Remove the three 4.3 mm Phillips screws from the bottom of the camera.

Remove the 4.3 mm Phillips screw hiding inside the battery compartment.

Step 6

Remove the 4.2 mm Phillips screw from the left handgrip.
Remove the two 4.2 mm Phillips screws from the right handgrip.

Remove the 4.2 mm Phillips screw from the left handgrip.

Remove the two 4.2 mm Phillips screws from the right handgrip.

Step 7

Use tweezers to remove the metal shield from the external flash mount.

Use tweezers to remove the metal shield from the external flash mount.

Step 8

Remove the four 5 mm Phillips screws from the external flash mount .

Remove the four 5 mm Phillips screws from the external flash mount .

Step 9

Remove the external flash mount.

Remove the external flash mount.

Step 10

Slowly pull the bottom of the back case away from the camera.
Do not attempt to remove the back case as it is attached to the motherboard by a ribbon cable.

Slowly pull the bottom of the back case away from the camera.

Do not attempt to remove the back case as it is attached to the motherboard by a ribbon cable.

Step 11

Use the flat end of a spudger to pry the flat topped connector straight up from the motherboard.
Remove the back case.

Use the flat end of a spudger to pry the flat topped connector straight up from the motherboard.

Remove the back case.

Step 12

LCD

To remove the metal shield on the back case, remove the following screws:
Five black 4.2 mm Phillips screws .
Four silver 5.3 mm Phillips screws.

To remove the metal shield on the back case, remove the following screws:

Five black 4.2 mm Phillips screws .

Four silver 5.3 mm Phillips screws.

Step 13

Insert the pointed end of a spudger into the whole on the ribbon cable holding the button panel to the back case.
Remove the button panel.

Insert the pointed end of a spudger into the whole on the ribbon cable holding the button panel to the back case.

Remove the button panel.

Step 14

Use a spudger to peel back the LCD ribbon from the back case.
The ribbon is held in place by adhesive.

Use a spudger to peel back the LCD ribbon from the back case.

The ribbon is held in place by adhesive.

Step 15

Use tweezers to remove the plastic cover on the LCD hinge.

Use tweezers to remove the plastic cover on the LCD hinge.

Step 16

Tilt the LCD so it lays flat against the back case.
Wiggle the LCD joints and pull the LCD away from the back case.

Tilt the LCD so it lays flat against the back case.

Wiggle the LCD joints and pull the LCD away from the back case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                    Kelsea Weber

Member since: 11/12/2015

18,948 Reputation

                                      32 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Raimo - Feb 12, 2021

Hello, Any Idea how to reset firmware after update did not succeed. Service manual for NX300 gives some glue but how about NX3000? Wherefrom to get the needed software pieces

Introduction#

What you need#

Team#

Introduction

What you need

Team