Difficulty
Moderate
Steps
14
Time Required
15 minutes
Sections
2
- Top Chassis
- 10 steps
- Vacuum Motor
- 4 steps
Flags
0
BackSamsung POWERbot VR9000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Chassis
- Turn off the emergency switch located at the bottom right of the POWERbot.
Turn off the emergency switch located at the bottom right of the POWERbot.
1024
Step 2
- Insert the plastic opening tool under the black cover, near the Samsung logo on the back of the device, and partially pry open.
Insert the plastic opening tool under the black cover, near the Samsung logo on the back of the device, and partially pry open.
Step 3
- Slide the plastic opening tool to the left, remaining under the black cover, until two left side pins have been detached. Then slide the plastic opening tool to the right until two right side pins have been detached.
- Grab the two clips near the front of the black cover, on in front of each wheel. Pull the clips away from the wheels.
Slide the plastic opening tool to the left, remaining under the black cover, until two left side pins have been detached. Then slide the plastic opening tool to the right until two right side pins have been detached.
Grab the two clips near the front of the black cover, on in front of each wheel. Pull the clips away from the wheels.
Step 4
- Remove the black cover.
Remove the black cover.
Step 5
- Insert the plastic opening tool under copper-colored cover, under the words “CycloneForce,” and pry open, applying a small rotation, until the two pins are released .
- Grab the underside of the cover and lift upwards while pushing forward until the cover pops off.
Insert the plastic opening tool under copper-colored cover, under the words “CycloneForce,” and pry open, applying a small rotation, until the two pins are released .
Grab the underside of the cover and lift upwards while pushing forward until the cover pops off.
Step 6
- Remove the three 6mm Phillips #1 screws in the holes near the back of the device.
Remove the three 6mm Phillips #1 screws in the holes near the back of the device.
Step 7
- Remove the 6mm Phillips #1 screw in the hole that was under the copper-colored vacuum cover.
Remove the 6mm Phillips #1 screw in the hole that was under the copper-colored vacuum cover.
Step 8
- Flip the device over and remove the 6mm Phillips #1 screw in front of the left (from this perspective, right) wheel.
Flip the device over and remove the 6mm Phillips #1 screw in front of the left (from this perspective, right) wheel.
Step 9
- Detach the wider circuit connector by pressing down gently on the left end of the clip and pulling the connector out.
- Pull the connector out by the top and bottom of the white piece and not by the wires.
Detach the wider circuit connector by pressing down gently on the left end of the clip and pulling the connector out.
Pull the connector out by the top and bottom of the white piece and not by the wires.
Step 10
- Remove the top chassis from the POWERbot by grabbing the wheel covers and lifting upwards.
Remove the top chassis from the POWERbot by grabbing the wheel covers and lifting upwards.
Step 11
Vacuum Motor
- Remove the three 5mm Phillips #1 screws in the holes around the vacuum motor.
Remove the three 5mm Phillips #1 screws in the holes around the vacuum motor.
Step 12
- Remove the 5mm Phillips #1 screw on the peg to the right of the circuit board.
Remove the 5mm Phillips #1 screw on the peg to the right of the circuit board.
Step 13
- Detach the largest circuit connector on the right side by pressing down gently on the right end of the clip and pulling the connector out.
- Pull the connector out by the top and bottom of the white piece and not by the wires.
Detach the largest circuit connector on the right side by pressing down gently on the right end of the clip and pulling the connector out.
Step 14
- Remove the vacuum motor by grabbing the body of the motor and lifting upwards.
Remove the vacuum motor by grabbing the body of the motor and lifting upwards.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 1 other contributor
Kyle Chin
Member since: 04/24/2017
1,919 Reputation
4 Guides authored
Badges:
16
+13 more badges
Team
Cal Poly, Team S15-G3, Banghart Spring 2017
Member of Cal Poly, Team S15-G3, Banghart Spring 2017
CPSU-BANGHART-S17S15G3
4 Members
14 Guides authored
