Difficulty
Moderate
Steps
14
Time Required
25 minutes
Sections
3
- Micro USB / Power Port Panel
- 5 steps
- 1" Tweeter Speaker
- 4 steps
- Bluetooth Module
- 5 steps
Flags
0
BackSamsung Radiant 360 R1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Micro USB / Power Port Panel
- Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.
- Use the plastic opening tool to lift and remove the rubber grommet plugs.
Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.
Use the plastic opening tool to lift and remove the rubber grommet plugs.
1024
Step 2
- Using a PH1 Philips screwdriver, remove four (9.5mm x 1.6mm) screws from the base plate.
- Remove base plate by stabilizing speaker and using plastic prying tool to pry the base plate from the speaker.
Using a PH1 Philips screwdriver, remove four (9.5mm x 1.6mm) screws from the base plate.
Remove base plate by stabilizing speaker and using plastic prying tool to pry the base plate from the speaker.
Step 3
- Place the speaker on the table with the Touch Pad facing down. This will leave you with the Port Panel exposed.
- Remove speaker grill by stabilizing speaker on a table and applying pressure to the bottom of the speaker. Slide the speaker grill up and away from the remaining endcap.
Place the speaker on the table with the Touch Pad facing down. This will leave you with the Port Panel exposed.
Remove speaker grill by stabilizing speaker on a table and applying pressure to the bottom of the speaker. Slide the speaker grill up and away from the remaining endcap.
Step 4
- Remove the two exposed (9.5mm x 1.6mm) PH1 Phillips screws on the Port Panel.
- Remove the Port Panel from the speaker body, exposing the ribbon cables.
Remove the two exposed (9.5mm x 1.6mm) PH1 Phillips screws on the Port Panel.
Remove the Port Panel from the speaker body, exposing the ribbon cables.
Step 5
- While stabilizing the Port Panel remove the two ribbon cables one at a time by pressing the locking clip down on the ribbon cable connectors and pulling the connector away from the Port Panel.
While stabilizing the Port Panel remove the two ribbon cables one at a time by pressing the locking clip down on the ribbon cable connectors and pulling the connector away from the Port Panel.
Step 6
1" Tweeter Speaker
- Remove the four (9.5mm x 1.6mm) PH1 Phillips screws on the port speaker body.
- Remove the Port Panel exposing the subwoofer.
Remove the four (9.5mm x 1.6mm) PH1 Phillips screws on the port speaker body.
Remove the Port Panel exposing the subwoofer.
Step 7
- Remove the eight (9.5mm x 1.6mm) PH1 Phillips screws on the right side of the speaker body.
- Remove the one (9.5mm x 1.6mm) PH1 Phillips screw on the left side of the speaker body.
- The body sides are denoted with a “R” and an “L” for right and left sides.
Remove the eight (9.5mm x 1.6mm) PH1 Phillips screws on the right side of the speaker body.
Remove the one (9.5mm x 1.6mm) PH1 Phillips screw on the left side of the speaker body.
The body sides are denoted with a “R” and an “L” for right and left sides.
Step 8
- Open up the body to expose the inner panel and motherboard.
Open up the body to expose the inner panel and motherboard.
Step 9
- Remove the ribbon cable from the tweeter which is attached to the main motherboard.
- Slide the tweeter out of the enclosure.
Remove the ribbon cable from the tweeter which is attached to the main motherboard.
Slide the tweeter out of the enclosure.
Step 10
Bluetooth Module
- Slide rubber grommet out of slot on plastic housing.
- This may have occurred naturally when separating the two halves.
Slide rubber grommet out of slot on plastic housing.
This may have occurred naturally when separating the two halves.
Step 11
- Disconnect white connector by pushing down on the release tab while gently pulling the connector free from the socket.
- Remove wiring harness and set aside.
- The other connectors in the wiring harness should already be free from previous steps.
Disconnect white connector by pushing down on the release tab while gently pulling the connector free from the socket.
Remove wiring harness and set aside.
The other connectors in the wiring harness should already be free from previous steps.
Step 12
- Locate and remove the two PH2 Phillips screws from the base of the motherboard assembly.
- These screws may be extremely tight. Be careful not to snap the plastic when removing the screws.
Locate and remove the two PH2 Phillips screws from the base of the motherboard assembly.
These screws may be extremely tight. Be careful not to snap the plastic when removing the screws.
Step 13
- Flip the motherboard assembly over and locate the Bluetooth module on the side of the metal frame.
- Remove the one PH2 Philips screw.
Flip the motherboard assembly over and locate the Bluetooth module on the side of the metal frame.
Remove the one PH2 Philips screw.
Step 14
- Press the white tab while gently pulling the Bluetooth module away from the connector and frame.
Press the white tab while gently pulling the Bluetooth module away from the connector and frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Daniel Mendoza
Member since: 02/01/2017
101 Reputation
1 Guide authored
Badges:
2
Team
UW Tacoma, Team 2-5, Rose Winter 2017
Member of UW Tacoma, Team 2-5, Rose Winter 2017
UWT-ROSE-W17S2G5
4 Members
4 Guides authored
Royce Courtney - Mar 11, 2021
Reply
Nice write up, but where does one obtain a new Bluetooth module for one of these?
Payout PH - Oct 20, 2021
Reply
Where can I buy these type of bluetooth module? Ty
