Samsung Radiant 360 R1 Touch Control Panel Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          25 minutes            

Sections

3

• Micro USB / Power Port Panel
• 5 steps
• 1" Tweeter Speaker
• 4 steps
• Touch Panel
• 2 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

• BackSamsung Radiant 360 R1

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Micro USB / Power Port Panel               

• Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.
• Use the plastic opening tool to lift and remove the rubber grommet plugs.

Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

Use the plastic opening tool to lift and remove the rubber grommet plugs.

1024

Step 2

• Using a PH1 Philips screwdriver, remove four (9.5mm x 1.6mm) screws from the base plate.
• Remove base plate by stabilizing speaker and using plastic prying tool to pry the base plate from the speaker.

Using a PH1 Philips screwdriver, remove four (9.5mm x 1.6mm) screws from the base plate.

Remove base plate by stabilizing speaker and using plastic prying tool to pry the base plate from the speaker.

Step 3

• Place the speaker on the table with the Touch Pad facing down. This will leave you with the Port Panel exposed.
• Remove speaker grill by stabilizing speaker on a table and applying pressure to the bottom of the speaker. Slide the speaker grill up and away from the remaining endcap.

Place the speaker on the table with the Touch Pad facing down. This will leave you with the Port Panel exposed.

Remove speaker grill by stabilizing speaker on a table and applying pressure to the bottom of the speaker. Slide the speaker grill up and away from the remaining endcap.

Step 4

• Remove the two exposed (9.5mm x 1.6mm) PH1 Phillips screws on the Port Panel.
• Remove the Port Panel from the speaker body, exposing the ribbon cables.

Remove the two exposed (9.5mm x 1.6mm) PH1 Phillips screws on the Port Panel.

Remove the Port Panel from the speaker body, exposing the ribbon cables.

Step 5

• While stabilizing the Port Panel remove the two ribbon cables one at a time by pressing the locking clip down on the ribbon cable connectors and pulling the connector away from the Port Panel.

While stabilizing the Port Panel remove the two ribbon cables one at a time by pressing the locking clip down on the ribbon cable connectors and pulling the connector away from the Port Panel.

Step 6

              1" Tweeter Speaker               

• Remove the four (9.5mm x 1.6mm) PH1 Phillips screws on the port speaker body.
• Remove the Port Panel exposing the subwoofer.

Remove the four (9.5mm x 1.6mm) PH1 Phillips screws on the port speaker body.

Remove the Port Panel exposing the subwoofer.

Step 7

• Remove the eight (9.5mm x 1.6mm) PH1 Phillips screws on the right side of the speaker body.
• Remove the one (9.5mm x 1.6mm) PH1 Phillips screw on the left side of the speaker body.
• The body sides are denoted with a “R” and an “L” for right and left sides.

Remove the eight (9.5mm x 1.6mm) PH1 Phillips screws on the right side of the speaker body.

Remove the one (9.5mm x 1.6mm) PH1 Phillips screw on the left side of the speaker body.

The body sides are denoted with a “R” and an “L” for right and left sides.

Step 8

• Open up the body to expose the inner panel and motherboard.

Open up the body to expose the inner panel and motherboard.

Step 9

• Remove the ribbon cable from the tweeter which is attached to the main motherboard.
• Slide the tweeter out of the enclosure.

Remove the ribbon cable from the tweeter which is attached to the main motherboard.

Slide the tweeter out of the enclosure.

Step 10

              Touch Panel               

• Separate the control panel from the base.

Separate the control panel from the base.

Step 11

• Control panel is now removed.

Control panel is now removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 5 other contributors 

                    Kim                     

Member since: 01/24/2017

128 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       UW Tacoma, Team 2-5, Rose Winter 2017                        

                                                  Member of UW Tacoma, Team 2-5, Rose Winter 2017 



                    UWT-ROSE-W17S2G5                     


                                            4 Members                     


                                            4 Guides authored