Samsung Radiant360 R3 Subwoofer Replacement Repair Guide

Difficulty

Moderate

Steps

17

Time Required

                          25 - 30 minutes            

Sections

3

• Wireless Setup Button and USB Module
• 5 steps
• Wireless Module
• 10 steps
• Subwoofer
• 2 steps

Flags

1

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

• BackSamsung Radiant360 R3

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Wireless Setup Button and USB Module               

• Flip the device so that the bottom of the device is facing you. Remove these feet with a pair of tweezers.
• Remove the four 10mm long screws with the Phillips #1 screwdriver.

Flip the device so that the bottom of the device is facing you. Remove these feet with a pair of tweezers.

Remove the four 10mm long screws with the Phillips #1 screwdriver.

1024

Step 2

• Remove the bottom shell from the speaker.

Remove the bottom shell from the speaker.

Step 3

• Remove the connector from the board by pressing down on the center tab while nudging the connector away with a spudger.
• Be careful not to pull directly on the wires or apply too much pressure, or you risk breaking the connector.

Remove the connector from the board by pressing down on the center tab while nudging the connector away with a spudger.

Be careful not to pull directly on the wires or apply too much pressure, or you risk breaking the connector.

Step 4

• Remove the two 10mm long screws from the board utilizing the Phillips #1 screwdriver.

Remove the two 10mm long screws from the board utilizing the Phillips #1 screwdriver.

Step 5

• Use a spudger to press the plastic tab away from the board until the board pops up.
• Remove the board with the USB module from the device.

Use a spudger to press the plastic tab away from the board until the board pops up.

Remove the board with the USB module from the device.

Step 6

              Wireless Module               

• Remove the two 12mm long screws with the Phillips #1 screwdriver.
• Unplug white plug connected to the green circuit board.

Remove the two 12mm long screws with the Phillips #1 screwdriver.

Unplug white plug connected to the green circuit board.

Step 7

• Remove the four 12mm long screws with the Phillips #1 screwdriver.
• Remove the cover, and slide the cord through the hole.

Remove the four 12mm long screws with the Phillips #1 screwdriver.

Remove the cover, and slide the cord through the hole.

Step 8

• Remove rubber covers covering the screws with pair of tweezers.
• Remove the six 12mm screws that are under the rubber covers with the Phillips #1 screwdriver.

Remove rubber covers covering the screws with pair of tweezers.

Remove the six 12mm screws that are under the rubber covers with the Phillips #1 screwdriver.

Step 9

• Remove the unscrewed cover as much as possible.
• It is very difficult to get plugs at the end of the cord through the cover without breaking, so just slide to the edge.

Remove the unscrewed cover as much as possible.

It is very difficult to get plugs at the end of the cord through the cover without breaking, so just slide to the edge.

Step 10

• Push the body out through the outer shell of device.
• Carefully push the ring attached to the cable through the shell.

Push the body out through the outer shell of device.

Carefully push the ring attached to the cable through the shell.

Step 11

• Remove the eight 12mm long screws around the body with the Phillips #1 screwdriver.

Remove the eight 12mm long screws around the body with the Phillips #1 screwdriver.

Step 12

• Pry the two halves of the body open using a metal spudger.

Pry the two halves of the body open using a metal spudger.

Step 13

• Remove the plugs located topmost right and closest to the bottom in picture.

Remove the plugs located topmost right and closest to the bottom in picture.

Step 14

• Remove the four 12mm long screws with the Phillips #1 screwdriver .

Remove the four 12mm long screws with the Phillips #1 screwdriver .

Step 15

• Unscrew the four 8mm screws on the side of the motherboard with the Phillips #1 screwdriver .
• Remove the Wireless Module from the device.

Unscrew the four 8mm screws on the side of the motherboard with the Phillips #1 screwdriver .

Remove the Wireless Module from the device.

Step 16

              Subwoofer               

• Disconnect the plug in the device.

Disconnect the plug in the device.

Step 17

• Slide the subwoofer out of the speaker.

Slide the subwoofer out of the speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Fadi Alzammar                     

Member since: 04/22/2018

782 Reputation

                                      5 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       Cal Poly, Team S25-G18, Maness Spring 2018                        

                                                  Member of Cal Poly, Team S25-G18, Maness Spring 2018 



                    CPSU-MANESS-S18S25G18                     


                                            4 Members                     


                                            5 Guides authored