Difficulty
Moderate
Steps
24
Time Required
40 - 45 minutes
Sections
5
- Wireless Setup Button and USB Module
- 5 steps
- Wireless Module
- 10 steps
- Subwoofer
- 2 steps
- Motherboard
- 3 steps
- Tweeter
- 4 steps
Flags
1
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackSamsung Radiant360 R3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Wireless Setup Button and USB Module
- Flip the device so that the bottom of the device is facing you. Remove these feet with a pair of tweezers.
- Remove the four 10mm long screws with the Phillips #1 screwdriver.
Flip the device so that the bottom of the device is facing you. Remove these feet with a pair of tweezers.
Remove the four 10mm long screws with the Phillips #1 screwdriver.
1024
Step 2
- Remove the bottom shell from the speaker.
Remove the bottom shell from the speaker.
Step 3
- Remove the connector from the board by pressing down on the center tab while nudging the connector away with a spudger.
- Be careful not to pull directly on the wires or apply too much pressure, or you risk breaking the connector.
Remove the connector from the board by pressing down on the center tab while nudging the connector away with a spudger.
Be careful not to pull directly on the wires or apply too much pressure, or you risk breaking the connector.
Step 4
- Remove the two 10mm long screws from the board utilizing the Phillips #1 screwdriver.
Remove the two 10mm long screws from the board utilizing the Phillips #1 screwdriver.
Step 5
- Use a spudger to press the plastic tab away from the board until the board pops up.
- Remove the board with the USB module from the device.
Use a spudger to press the plastic tab away from the board until the board pops up.
Remove the board with the USB module from the device.
Step 6
Wireless Module
- Remove the two 12mm long screws with the Phillips #1 screwdriver.
- Unplug white plug connected to the green circuit board.
Remove the two 12mm long screws with the Phillips #1 screwdriver.
Unplug white plug connected to the green circuit board.
Step 7
- Remove the four 12mm long screws with the Phillips #1 screwdriver.
- Remove the cover, and slide the cord through the hole.
Remove the four 12mm long screws with the Phillips #1 screwdriver.
Remove the cover, and slide the cord through the hole.
Step 8
- Remove rubber covers covering the screws with pair of tweezers.
- Remove the six 12mm screws that are under the rubber covers with the Phillips #1 screwdriver.
Remove rubber covers covering the screws with pair of tweezers.
Remove the six 12mm screws that are under the rubber covers with the Phillips #1 screwdriver.
Step 9
- Remove the unscrewed cover as much as possible.
- It is very difficult to get plugs at the end of the cord through the cover without breaking, so just slide to the edge.
Remove the unscrewed cover as much as possible.
It is very difficult to get plugs at the end of the cord through the cover without breaking, so just slide to the edge.
Step 10
- Push the body out through the outer shell of device.
- Carefully push the ring attached to the cable through the shell.
Push the body out through the outer shell of device.
Carefully push the ring attached to the cable through the shell.
Step 11
- Remove the eight 12mm long screws around the body with the Phillips #1 screwdriver.
Remove the eight 12mm long screws around the body with the Phillips #1 screwdriver.
Step 12
- Pry the two halves of the body open using a metal spudger.
Pry the two halves of the body open using a metal spudger.
Step 13
- Remove the plugs located topmost right and closest to the bottom in picture.
Remove the plugs located topmost right and closest to the bottom in picture.
Step 14
- Remove the four 12mm long screws with the Phillips #1 screwdriver .
Remove the four 12mm long screws with the Phillips #1 screwdriver .
Step 15
- Unscrew the four 8mm screws on the side of the motherboard with the Phillips #1 screwdriver .
- Remove the Wireless Module from the device.
Unscrew the four 8mm screws on the side of the motherboard with the Phillips #1 screwdriver .
Remove the Wireless Module from the device.
Step 16
Subwoofer
- Disconnect the plug in the device.
Disconnect the plug in the device.
Step 17
- Slide the subwoofer out of the speaker.
Slide the subwoofer out of the speaker.
Step 18
Motherboard
- Disconnect the six plugs on the motherboard.
Disconnect the six plugs on the motherboard.
Step 19
- Remove the ZIF cable.
- Pull up the tab with a spudger, and life the cable.
Remove the ZIF cable.
Pull up the tab with a spudger, and life the cable.
Step 20
- Remove the four 12mm screws with the Phillips #1 screwdriver .
- Remove the motherboard from the device.
Remove the four 12mm screws with the Phillips #1 screwdriver .
Remove the motherboard from the device.
Step 21
Tweeter
- Remove the six 8mm screws using the Phillips #1 screwdriver.
- Remove the six 12mm screws using the Phillips #1 screwdriver.
Remove the six 8mm screws using the Phillips #1 screwdriver.
Remove the six 12mm screws using the Phillips #1 screwdriver.
Step 22
- Remove the six 12mm screws with the Phillips #1 screwdriver.
Remove the six 12mm screws with the Phillips #1 screwdriver.
Step 23
- Remove the touch panel by sliding it off the end.
Remove the touch panel by sliding it off the end.
Step 24
- Remove the tweeter speaker from the casing.
Remove the tweeter speaker from the casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Fadi Alzammar
Member since: 04/22/2018
782 Reputation
5 Guides authored
Badges:
5
+2 more badges
Team
Cal Poly, Team S25-G18, Maness Spring 2018
Member of Cal Poly, Team S25-G18, Maness Spring 2018
CPSU-MANESS-S18S25G18
4 Members
5 Guides authored
