Difficulty
Moderate
Steps
10
Time Required
10 - 15 minutes
Sections
3
- Battery
- 2 steps
- Front and Back Case
- 3 steps
- Camera Lens
- 5 steps
Flags
0
BackSamsung S760
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Placing your thumb on the battery cover, push outwards, away from the camera in the direction the arrow is pointing. If done correctly when it’s completely unhooked, the latch will open.
Placing your thumb on the battery cover, push outwards, away from the camera in the direction the arrow is pointing. If done correctly when it’s completely unhooked, the latch will open.
1024
Step 2
- Tip the camera as to gently slide the batteries out of the camera.
Tip the camera as to gently slide the batteries out of the camera.
Step 3
Front and Back Case
- All screws in this camera are removed using the Phillip Screwdriver #000 bit. Also, all dimensions included refer to screw lengths.
- Locate and remove the six 4mm screws on the sides of the camera.
All screws in this camera are removed using the Phillip Screwdriver #000 bit. Also, all dimensions included refer to screw lengths.
Locate and remove the six 4mm screws on the sides of the camera.
Step 4
- Use the plastic opening tool to pry open the back case, following alongside the edge of the case if need be.
Use the plastic opening tool to pry open the back case, following alongside the edge of the case if need be.
Step 5
- Once the back case is removed, use the plastic opening tool to gently pry off the front case.
Once the back case is removed, use the plastic opening tool to gently pry off the front case.
Step 6
Camera Lens
- Move the screen down, out of the way to remove the two 3mm screws beneath it.
Move the screen down, out of the way to remove the two 3mm screws beneath it.
Step 7
- Remove the 6mm screw labeled in the picture.
- Remove the three 3mm screws.
- Then proceed to flip the screen to the other side to remove the other 6mm screw.
Remove the 6mm screw labeled in the picture.
Remove the three 3mm screws.
Then proceed to flip the screen to the other side to remove the other 6mm screw.
Step 8
- Proceed to carefully pull the ribbon cable out by using the little circular tabs sticking out on either side.
Proceed to carefully pull the ribbon cable out by using the little circular tabs sticking out on either side.
Step 9
- Proceed to slowly pry off the mother board with the plastic opening tool by removing it at the micro USB attachment.
- Then carefully manually pry off the golden colored section near the camera wheel until all of it is off.
Proceed to slowly pry off the mother board with the plastic opening tool by removing it at the micro USB attachment.
Then carefully manually pry off the golden colored section near the camera wheel until all of it is off.
Step 10
- Finally, remove the final 3mm screw marked in the picture.
- Lift the camera lens out of the lens compartment.
Finally, remove the final 3mm screw marked in the picture.
Lift the camera lens out of the lens compartment.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
David Sepulveda
Member since: 03/06/2017
404 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
UMass Dartmouth, Team S8-G1, Catania Spring 2017
Member of UMass Dartmouth, Team S8-G1, Catania Spring 2017
UMASSD-CATANIA-S17S8G1
3 Members
11 Guides authored
frankasensale - Jun 25, 2019
Reply
Brilliantly explained. Makes it look so easy… even a fool such as I could follow the instructions.
