Difficulty
Difficult
Steps
10
Time Required
30 minutes
Sections
1
- Screen
- 10 steps
Flags
0
BackSamsung SGH-T639
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Flip phone over and locate the screw covers.
- Remove the two thin screw covers using the tweezers.
Flip phone over and locate the screw covers.
Remove the two thin screw covers using the tweezers.
1024
Step 2
- Locate the two screws (3mm) at the base of the top portion of the cell phone.
- Remove screws using a phillips head #000 screwdriver.
- Place screws on magnetic mat.
Locate the two screws (3mm) at the base of the top portion of the cell phone.
Remove screws using a phillips head #000 screwdriver.
Place screws on magnetic mat.
Step 3
- Locate the seam of the casing along the edge of the phone.
- Starting at the end, gently begin to pry the front casing away from the phone. Use the plastic opening tool for this step.
Locate the seam of the casing along the edge of the phone.
Starting at the end, gently begin to pry the front casing away from the phone. Use the plastic opening tool for this step.
Step 4
- Continue to pry the casing from the front of the cell phone.
- Remove front casing from the cell phone.
Continue to pry the casing from the front of the cell phone.
Remove front casing from the cell phone.
Step 5
- Locate the small battery at the end of the cell phone.
- Gently remove the battery from the cell phone using tweezers.
- Note: This may require some force.
- Do not disconnect the battery from the entire phone. Simply lift the battery from the cell phone while keeping the wires connected.
Locate the small battery at the end of the cell phone.
Gently remove the battery from the cell phone using tweezers.
Note: This may require some force.
Do not disconnect the battery from the entire phone. Simply lift the battery from the cell phone while keeping the wires connected.
Step 6
- Locate the speaker at the end of the cell phone.
- Gently grasp and lift the speaker from the cell phone using tweezers.
- Do not disconnect the speaker from the entire cell phone. Simply lift the speaker while leaving the wires connected.
Locate the speaker at the end of the cell phone.
Gently grasp and lift the speaker from the cell phone using tweezers.
Do not disconnect the speaker from the entire cell phone. Simply lift the speaker while leaving the wires connected.
Step 7
- Locate the tip of the sheer protection film.
- Gently lift and remove the protection film with tweezers.
Locate the tip of the sheer protection film.
Gently lift and remove the protection film with tweezers.
Step 8
- Locate the top tabs of the screen and circuit board unit
- Gently lift the screen and circuit board as one unit from the cell phone using the tweezers.
- Make sure the screen and circuit board are removed as one unit. Do not disconnect the screen from the circuit board.
Locate the top tabs of the screen and circuit board unit
Gently lift the screen and circuit board as one unit from the cell phone using the tweezers.
Make sure the screen and circuit board are removed as one unit. Do not disconnect the screen from the circuit board.
Step 9
- Locate the gold connector that is attached to the circuit board.
- Pull the connection away from the circuit board.
- Note: This may require some force.
Locate the gold connector that is attached to the circuit board.
Pull the connection away from the circuit board.
Step 10
- Completely remove the screen and circuit board unit from the cell phone.
Completely remove the screen and circuit board unit from the cell phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Yi Ren
Member since: 03/26/2014
801 Reputation
8 Guides authored
Badges:
4
+1 more badge
Team
Clemson, Team 1-4, Benson Spring 2014
Member of Clemson, Team 1-4, Benson Spring 2014
CLEM-BENSON-S14S1G4
3 Members
16 Guides authored
