Samsung Stratosphere Front Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 - 45 minutes

Sections

Battery
2 steps
Motherboard
6 steps
Front Camera
9 steps

Flags

BackSamsung Stratosphere
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Using your fingers, pry along the groove at the top of the phone.
Pull back on the rear casing until it comes free from the device.
The casing will make a cracking sound as it is removed.

Using your fingers, pry along the groove at the top of the phone.

Pull back on the rear casing until it comes free from the device.

The casing will make a cracking sound as it is removed.

1024

Step 2

With your fingers, pry from the bottom of the battery to loosen it.
Lift away to remove the battery from the phone.

With your fingers, pry from the bottom of the battery to loosen it.

Lift away to remove the battery from the phone.

Step 3

              Motherboard

Locate the red and white sim card located above the battery housing.
Remove the sim card by sliding it downwards from its slot with your fingers.

Locate the red and white sim card located above the battery housing.

Remove the sim card by sliding it downwards from its slot with your fingers.

Step 4

Remove the seven silver 3mm screws securing the rear panel using the Phillips #000 screwdriver.
Once loosened, some screws may get stuck in the casing. Use tweezers to remove them.

Remove the seven silver 3mm screws securing the rear panel using the Phillips #000 screwdriver.

Once loosened, some screws may get stuck in the casing. Use tweezers to remove them.

Step 5

Pry around the rear panel with a plastic opening tool to loosen it.
Prying too deeply may damage delicate components inside the phone.
Remove the rear panel from the phone with your fingers.

Pry around the rear panel with a plastic opening tool to loosen it.

Prying too deeply may damage delicate components inside the phone.

Remove the rear panel from the phone with your fingers.

Step 6

Remove the four black 3mm screws securing the motherboard with the Phillips #000 screwdriver.

Remove the four black 3mm screws securing the motherboard with the Phillips #000 screwdriver.

Step 7

Locate the flex cable attachment at the tab with a green arrow printed on top.
Pry from the side the arrow is pointing with your fingers.
The cable will audibly snap as it is removed from its attachment.
Let the cable hang loosely to the side of the phone.

Locate the flex cable attachment at the tab with a green arrow printed on top.

Pry from the side the arrow is pointing with your fingers.

The cable will audibly snap as it is removed from its attachment.

Let the cable hang loosely to the side of the phone.

Step 8

Pull the motherboard up from the side opposite the loose flex cable.
If necessary, use a plastic opening tool to separate the motherboard from the key pad underneath.
Lift to remove the motherboard from the device.

Pull the motherboard up from the side opposite the loose flex cable.

If necessary, use a plastic opening tool to separate the motherboard from the key pad underneath.

Lift to remove the motherboard from the device.

Step 9

              Front Camera

Insert a plastic opening tool into any side of the phone case to separate the keyboard from the rear panel.
Pry the keyboard away from the casing with the plastic opening tool.
The keyboard should come off with almost no force at all.

Insert a plastic opening tool into any side of the phone case to separate the keyboard from the rear panel.

Pry the keyboard away from the casing with the plastic opening tool.

The keyboard should come off with almost no force at all.

Step 10

Remove the 7 silver 2mm screws attaching the silver metal plate to the rear panel with the Phillips #000 Screwdriver.

Remove the 7 silver 2mm screws attaching the silver metal plate to the rear panel with the Phillips #000 Screwdriver.

Step 11

Use the plastic opening tool to carefully loosen the golden metal plate.
The golden metal plate is stuck to the rear panel with a strong adhesive, so a moderate amount of force may be needed.

Use the plastic opening tool to carefully loosen the golden metal plate.

The golden metal plate is stuck to the rear panel with a strong adhesive, so a moderate amount of force may be needed.

Step 12

Lift the gold plate with your fingers, repositioning it to slide through the keyboard casing underneath.
Carefully take off the keyboard casing with your fingers.
The golden metal plate should fit through the wide slot of the casing.

Lift the gold plate with your fingers, repositioning it to slide through the keyboard casing underneath.

Carefully take off the keyboard casing with your fingers.

The golden metal plate should fit through the wide slot of the casing.

Step 13

Slide the silver metal plate down and away from the to the flex cable and gold metal plate.
The metal plate is attached to springs that offer a small amount of resistance, so it will snap into place.

Slide the silver metal plate down and away from the to the flex cable and gold metal plate.

The metal plate is attached to springs that offer a small amount of resistance, so it will snap into place.

Step 14

Unscrew the 4 black 3mm screws from the rear panel with the Phillips #000 Screwdriver.

Unscrew the 4 black 3mm screws from the rear panel with the Phillips #000 Screwdriver.

Step 15

Insert the plastic opening tool into the groove at the top of the rear panel.
Firmly slide the plastic opening tool all around the rear panel. The panel will audibly snap as it comes apart.
These 2 pieces are attached well, so a significant amount of force is needed to separate them.

Insert the plastic opening tool into the groove at the top of the rear panel.

Firmly slide the plastic opening tool all around the rear panel. The panel will audibly snap as it comes apart.

These 2 pieces are attached well, so a significant amount of force is needed to separate them.

Step 16

Lift the flex cable and position it so the part containing the metal plate can come free.
Pull the part containing the metal plate away from the rest of the rear panel.

Lift the flex cable and position it so the part containing the metal plate can come free.

Pull the part containing the metal plate away from the rest of the rear panel.

Step 17

Use tweezers to loosen the front-facing camera from the plastic casing.
Pull the black rectangular piece, attached to the front facing camera, away from the rear panel.

Use tweezers to loosen the front-facing camera from the plastic casing.

Pull the black rectangular piece, attached to the front facing camera, away from the rear panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Ryan

Member since: 10/20/2013

375 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 11-32, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 11-32, Amido Fall 2013 



                    CPSU-AMIDO-F13S11G32                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team