Difficulty

Moderate

Steps

13

Time Required

                          20 - 25 minutes

Sections

3

  • Outer Shell
  • 4 steps
  • Fan A
  • 4 steps
  • Motherboard
  • 5 steps

Flags

1

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

  • BackSamsung UBD-KM85C

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Shell
  • On the back side of the unit, remove the three 8.1mm screws marked with a Phillips #1 screwdriver.

On the back side of the unit, remove the three 8.1mm screws marked with a Phillips #1 screwdriver.

1024

Step 2

  • From the back, lift the case upwards away from the unit then forwards, releasing the prongs on the front.

From the back, lift the case upwards away from the unit then forwards, releasing the prongs on the front.

Step 3

  • There is one group of wires located towards the front of the case and attached directly to the motherboard and the case. Using two fingers in a pinching motion, release the wire from the clip and disconnect it.

There is one group of wires located towards the front of the case and attached directly to the motherboard and the case. Using two fingers in a pinching motion, release the wire from the clip and disconnect it.

Step 4

  • Remove the cover from the device.

Remove the cover from the device.

Step 5

              Fan A
  • Fan A is located on top of the motherboard and is screwed into a stand by two 6.5mm screws. The stand is also connected to the motherboard.

Fan A is located on top of the motherboard and is screwed into a stand by two 6.5mm screws. The stand is also connected to the motherboard.

Step 6

  • The two 6.5mm screws holding the fan in place on opposing corners must be removed with a #1 Phillips head screwdriver to change the fan.

The two 6.5mm screws holding the fan in place on opposing corners must be removed with a #1 Phillips head screwdriver to change the fan.

Step 7

  • There is one wire connecting the fan to the motherboard that must be unplugged in order to release it. To unplug, use your fingers to pinch the white clip at the end and gently pull upwards to release.

There is one wire connecting the fan to the motherboard that must be unplugged in order to release it. To unplug, use your fingers to pinch the white clip at the end and gently pull upwards to release.

Step 8

  • The fan can now be lifted from the stand.

The fan can now be lifted from the stand.

Step 9

              Motherboard
  • The motherboard is in the middle of the device and has all wires and connections of the device components running to it. The fan identified as fan A is located on top of it and must be removed first.

The motherboard is in the middle of the device and has all wires and connections of the device components running to it. The fan identified as fan A is located on top of it and must be removed first.

Step 10

  • Once the fan is removed, the wires should be disconnected from the motherboard, as shown.

Once the fan is removed, the wires should be disconnected from the motherboard, as shown.

Step 11

  • Two outer 8.1mm screws located above the HDMI ports hold the motherboard in place and must be removed. Remove these with a #1 Phillips head screwdriver.

Two outer 8.1mm screws located above the HDMI ports hold the motherboard in place and must be removed. Remove these with a #1 Phillips head screwdriver.

Step 12

  • Three inner 6.5mm Phillips #1 screws hold the motherboard to the base of the frame, and must be unscrewed next.

Three inner 6.5mm Phillips #1 screws hold the motherboard to the base of the frame, and must be unscrewed next.

Step 13

  • After the final screw is removed, the motherboard can be easily lifted out of the case without disturbing any of the other device components.

After the final screw is removed, the motherboard can be easily lifted out of the case without disturbing any of the other device components.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    James Edwards

Member since: 02/01/2018

627 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Baylor, Team S2-G1, Johnson Spring 2018                        

                                                  Member of Baylor, Team S2-G1, Johnson Spring 2018 



                    BU-JOHNSON-S18S2G1                     


                                            3 Members                     


                                            6 Guides authored