Difficulty
Moderate
Steps
11
Time Required
20 minutes
Sections
4
- Battery
- 2 steps
- LCD Screen
- 6 steps
- Motherboard
- 2 steps
- Lens Assembly
- 1 step
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackSamsung WB150F
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
A camera lens is a tool used to bring light to a fixed focal point.
Before using this guide, inspect the battery to ensure that the device is receiving power.
Prior to beginning, make sure to remove the battery from your camera and disconnect from any external power source.
What you need
Step 1
Battery
- The location of the battery compartment can be found on the underside of the camera.
The location of the battery compartment can be found on the underside of the camera.
1024
Step 2
- Have the lens of the camera face you. To open the battery compartment, slide the battery door lock towards the left. At the same time allow the battery door to swing open.
Have the lens of the camera face you. To open the battery compartment, slide the battery door lock towards the left. At the same time allow the battery door to swing open.
Step 3
LCD Screen
- Gather a PHO Phillips head screwdriver and a plastic wedge. If you do not have a plastic wedge like the one pictured, a credit card or a guitar pick can be used.
Gather a PHO Phillips head screwdriver and a plastic wedge. If you do not have a plastic wedge like the one pictured, a credit card or a guitar pick can be used.
Step 4
- Take off the front casing by using your screwdriver to unscrew the screws circled in each of the photos (5 total).
- The front casing can now be pulled from the camera.
Take off the front casing by using your screwdriver to unscrew the screws circled in each of the photos (5 total).
The front casing can now be pulled from the camera.
Step 5
- Your camera should now look like the camera in the photo.
Your camera should now look like the camera in the photo.
Step 6
- Flip the camera over and pry the back shell of the camera off with the plastic opening tool (or credit card or guitar pick). The screen-side of your camera should now resemble the camera in the second photo.
- Note: removing the back shell does not require removing anymore screws, it should just snap off.
Flip the camera over and pry the back shell of the camera off with the plastic opening tool (or credit card or guitar pick). The screen-side of your camera should now resemble the camera in the second photo.
Note: removing the back shell does not require removing anymore screws, it should just snap off.
Step 7
- On the screen side, remove the button circuit board (outlined in red) from the camera by using the plug located in the upper right corner of the screen side.
On the screen side, remove the button circuit board (outlined in red) from the camera by using the plug located in the upper right corner of the screen side.
Step 8
- Remove the metal casing by lifting up the old screen and unscrewing the 5 screws circled in the first photo.
- The LCD screen has a ribbon going to the main circuit board, as shown in the second photo, that needs to be detached.
- Your camera should now resemble the third photo.
Remove the metal casing by lifting up the old screen and unscrewing the 5 screws circled in the first photo.
The LCD screen has a ribbon going to the main circuit board, as shown in the second photo, that needs to be detached.
Your camera should now resemble the third photo.
Step 9
Motherboard
- Disconnect the ribbon from the flash assembly.
- Disconnect two ribbons from the lens assembly as shown in the second picture.
- Disconnect the ground wire from the motherboard as shown in the third picture.
Disconnect the ribbon from the flash assembly.
Disconnect two ribbons from the lens assembly as shown in the second picture.
Disconnect the ground wire from the motherboard as shown in the third picture.
Step 10
- Remove the motherboard from the camera housing.
Remove the motherboard from the camera housing.
Step 11
Lens Assembly
- Lens assembly freely detaches from housing once both ribbons are detached from the motherboard.
Lens assembly freely detaches from housing once both ribbons are detached from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Wyatt Turner
Member since: 04/12/2022
265 Reputation
3 Guides authored
Badges:
3
Team
IUPUI, Team 7-7, Beck Spring 2022
Member of IUPUI, Team 7-7, Beck Spring 2022
IUPUI-BECK-S22S7G7
4 Members
3 Guides authored
